Source author record

Roger K. Lake

Roger K. Lake appears in the imported research catalog. Authorship, coauthor and topic links are available while profile ownership is still unclaimed.

ResearcherUnclaimed source record

cond-mat.mes-hall cond-mat.mtrl-sci cond-mat.other physics.app-ph cond-mat.str-el cond-mat.supr-con nlin.PS

Catalog footprint

What is connected

19works

7topics

4close collaborators

Actions

Connect this record

Open graph Browse works

Inspect adjacent papers, topics, institutions and collaborators without losing the researcher page.

Building this map preview

BZPEER is loading the nearby papers, people, topics and institutions for this page.

preprint2026arXiv

A Quieter State of Charge -- Ultra-Low-Noise Collective Current in Charge-Density-Wave Nanowires

Electronic flicker noise limits phase stability in communication systems, reduces the sensitivity and selectivity of sensors, and degrades coherence in quantum devices. There is a strong need for unconventional materials and strategies for achieving ultra-low-noise performance in nanoscale and quantum electronics. Here, we demonstrate that in nanowires of the quasi-one-dimensional, fully gapped charge-density-wave material (TaSe4)2I, low-frequency electronic noise is suppressed below the limit of thermalized charge carriers in passive resistors. When the current is dominated by the sliding Frohlich condensate, the normalized noise spectral density decreases linearly with current, I -- a striking departure from the constant value observed in conventional conductors. No residual minimum noise level is reached for the current of the electron-lattice condensate in (TaSe4)2I nanowires. Repeating the measurements for another charge-density wave conductor, NbS3-II, we found a similar reduction below the normal electron limit at room temperature. Our findings signal intrinsically lower current fluctuations within a correlated electron transport regime.

preprint2023arXiv

Structural tuning magnetism and topology in a magnetic topological insulator

To date, the most widely-studied quantum anomalous Hall insulator (QAHI) platform is achieved by dilute doping of magnetic ions into thin films of the alloyed tetradymite topological insulator (TI) (Bi$_{1-x}$Sb$_x$)$_2$Te$_3$ (BST). In these films, long-range magnetic ordering of the transition metal substituants opens an exchange gap $Δ$ in the topological surface states, stabilizing spin-polarized, dissipationless edge channels with a nonzero Chern number $\mathcal{C}$. The long-range ordering of the spatially separated magnetic ions is itself mediated by electronic states in the host TI, leading to a sophisticated feedback between magnetic and electronic properties. Here we present a study of the electronic and magnetic response of a BST-based QAHI system to structural tuning via hydrostatic pressure. We identify a systematic closure of the topological gap under compressive strain accompanied by a simultaneous enhancement in the magnetic ordering strength. Combining these experimental results with first-principle calculations we identify structural deformation as a strong tuning parameter to traverse a rich topological phase space and modify magnetism in the magnetically doped BST system.

preprint2022arXiv

One-Dimensional van der Waals Quantum Materials -- State of the Art and Perspectives

The advent of graphene and other two-dimensional van der Waals materials, with their unique electrical, optical, and thermal properties, has resulted in tremendous progress for fundamental science. Recent developments suggest that taking one more step down in dimensionality - from monolayer, atomic sheets to individual atomic chains - can bring exciting prospects as the ultimate limit in material downscaling is reached while establishing an entirely new field of one-dimensional quantum materials. Here we review this emerging area of one-dimensional van der Waals quantum materials and anticipate its future directions. We focus on quantum effects associated with the charge-density-wave condensate, strongly-correlated phenomena, topological phases, and other unique physical characteristics, which are attainable specifically in van der Waals materials of lower dimensionality. Possibilities for engineering the properties of quasi-one-dimensional materials via compositional changes, vacancies, and defects, as well as the prospects of their applications in composites are also discussed.

preprint2022arXiv

Tuning Spin Transport in a Graphene Antiferromagnetic Insulator

Long-distance spin transport through anti-ferromagnetic insulators (AFMIs) is a long-standing goal of spintronics research. Unlike conventional spintronics systems, monolayer graphene in quantum Hall regime (QH) offers an unprecedented tuneability of spin-polarization and charge carrier density in QH edge states. Here, using gate-controlled QH edges as spin-dependent injectors and detectors in an all-graphene electrical circuit, for the first time we demonstrate a selective tuning of ambipolar spin transport through graphene $ν$=0 AFMIs. By modulating polarities of the excitation bias, magnetic fields, and charge carriers that host opposite chiralities, we show that the difference between spin chemical potentials of adjacent edge channels in the spin-injector region is crucial in tuning spin-transport observed across graphene AFMI. We demonstrate that non-local response vanishes upon reversing directions of the co-propagating edge channels when the spin-filters in our devices are no longer selective for a particular spin-polarization. Our results establish a versatile set of methods to tune pure spin transport via an anti-ferromagnetic media and open a pathway to explore their applications for a broad field of antiferromagnetic spintronics research.

preprint2020arXiv

Effects of filling, strain, and electric field on the Néel vector in antiferromagnetic CrSb

CrSb is a layered antiferromagnet (AFM) with perpendicular magnetic anisotropy, a high Néel temperature, and large spin-orbit coupling (SOC), which makes it interesting for AFM spintronic applications. To elucidate the various mechanisms of Néel vector control, the effects of strain, band filling, and electric field on the magnetic anisotropy energy (MAE) of bulk and thin-film CrSb are determined and analysed using density functional theory. The MAE of the bulk crystal is large (1.2 meV per unit cell). Due to the significant ionic nature of the Cr-Sb bond, finite slabs are strongly affected by end termination. Truncation of the bulk crystal to a thin film with one surface terminated with Cr and the other surface terminated with Sb breaks inversion symmetry, creates a large charge dipole and average electric field across the film, and breaks spin degeneracy, such that the thin film becomes a ferrimagnet. The MAE is reduced such that its sign can be switched with realistic strain, and the large SOC gives rise to an intrinsic voltage controlled magnetic anisotropy (VCMA). A slab terminated on both faces with Cr remains a compensated AFM, but with the compensation occurring nonlocally between mirror symmetric Cr pairs. In-plane alignment of the moments is preferred, the magnitude of the MAE remains large, similar to that of the bulk, and it is relatively insensitive to filling.

preprint2020arXiv

Electron transport through antiferromagnetic spin textures and skyrmions in a magnetic tunnel junction

An ideal layered $\hat{x}$-polarized antiferromagnet (AFM) between two antialigned $\pm \hat{z}$ polarized ferromagnetic (FM) contacts transmits no current due to a $π$ phase difference of the matrix elements coupling the spin degenerate states to the two FM contacts. The ratio of the two matrix elements coupling the two spin degenerate $\hat{x}$ AFM states to a $\hat{z}$ FM contact is determined by the exchange energy and the eigenstate energy. Inserting a normal metal layer or tunnel barrier layer between one FM contact and the AFM alters this phase difference, and, due to the unequal weighting of the two spins at the interface, it also breaks the spin degeneracy of the two AFM states. The broken symmetry of the matrix elements combined with the broken degeneracy of the AFM states, result in a Fano resonance in the transmission and a turn-on of the $T_{\uparrow,\downarrow}$ transmission channel. Such a magnetic tunnel junction geometry with two antialigned $\pm \hat{z}$ FM contacts can electrically detect an AFM skyrmion. The AFM skyrmion serves as an analogue of the oblique polarizer in the triple polarizer experiment. Resistances and resistance ratios are calculated and compared for FM and AFM skyrmions in a magnetic tunnel junction.

preprint2020arXiv

Interfacial Dzyaloshinskii-Moriya Interaction of Antiferromagnetic Materials

The interface between a ferromagnet (FM) or antiferromagnet (AFM) and a heavy metal (HM) results in an antisymmetric exchange interaction known as the interfacial Dzyaloshinskii-Moriya interaction (iDMI) which favors non-collinear spin configurations. The iDMI is responsible for stabilizing noncollinear spin textures such as skyrmions in materials with bulk inversion symmetry. Interfacial DMI values have been previously determined theoretically and experimentally for FM/HM interfaces, and, in this work, values are calculated for the metallic AFM MnPt and the insulating AFM NiO. The heavy metals considered are W, Re, and Au. The effects of the AFM and HM thicknesses are determined. The iDMI values of the MnPt heterolayers are comparable to those of the common FM materials, and those of NiO are lower.

preprint2020arXiv

Large spin-Hall effect in Si at room temperature

Silicon's weak intrinsic spin-orbit coupling and centrosymmetric crystal structure are a critical bottleneck to the development of Si spintronics, because they lead to an insignificant spin-Hall effect (spin current generation) and inverse spin-Hall effect (spin current detection). Here, we undertake current, magnetic field, crystallography dependent magnetoresistance and magneto thermal transport measurements to study the spin transport behavior in freestanding Si thin films. We observe a large spin-Hall magnetoresistance in both p-Si and n-Si at room temperature and it is an order of magnitude larger than that of Pt. One explanation of the unexpectedly large and efficient spin-Hall effect is spin-phonon coupling instead of spin-orbit coupling. The macroscopic origin of the spin-phonon coupling can be large strain gradients that can exist in the freestanding Si films. This discovery in a light, earth abundant and centrosymmetric material opens a new path of strain engineering to achieve spin dependent properties in technologically highly-developed materials.

preprint2020arXiv

Properties of Shape-Engineered Phoxonic Crystals: Brillouin-Mandelstam Spectroscopy and Ellipsometry Study

We report the results of Brillouin-Mandelstam spectroscopy and Mueller matrix spectroscopic ellipsometry of the nanoscale "pillar with the hat" periodic silicon structures, revealing intriguing phononic and photonic properties. It has been theoretically shown that periodic structures with properly tuned dimensions can act simultaneously as phononic and photonic - phoxonic - crystals, strongly affecting the light-matter interactions. Acoustic phonon states can be tuned by external boundaries, either as a result of phonon confinement effects in individual nanostructures, or as a result of artificially induced external periodicity, as in the phononic crystals. The shape of the nanoscale pillar array was engineered to ensure the interplay of both effects. The Brillouin-Mandelstam spectroscopy data indicated strong flattening of the acoustic phonon dispersion in the frequency range from 2 GHz to 20 GHz and the phonon wave vector extending to the higher-order Brillouin zones. The specifics of the phonon dispersion dependence on the pillar arrays orientation suggest the presence of both periodic modulation and spatial localization effects for the acoustic phonons. The ellipsometry data reveal a distinct scatter pattern of four-fold symmetry due to nanoscale periodicity of the pillar arrays. Our results confirm the dual functionality of the nanostructured shape-engineered structure and indicate a possible new direction for fine-tuning the light-matter interaction in the next generation of photonic, optoelectronic, and phononic devices.

preprint2020arXiv

Strain controlled superconductivity in few-layer NbSe2

The controlled tunability of superconductivity in low-dimensional materials may enable new quantum devices. Particularly in triplet or topological superconductors, tunneling devices such as Josephson junctions etc. can demonstrate exotic functionalities. The tunnel barrier, an insulating or normal material layer separating two superconductors, is a key component for the junctions. Thin layers of NbSe2 have been shown as a superconductor with strong spin orbit coupling, which can give rise to topological superconductivity if driven by a large magnetic exchange field. Here we demonstrate the superconductor-insulator transitions in epitaxially grown few-layer NbSe2 with wafer-scale uniformity on insulating substrates. We provide the electrical transport, Raman spectroscopy, cross-sectional transmission electron microscopy, and X-ray diffraction characterizations of the insulating phase. We show that the superconductor-insulator transition is driven by strain, which also causes characteristic energy shifts of the Raman modes. Our observation paves the way for high quality hetero-junction tunnel barriers to be seamlessly built into epitaxial NbSe2 itself, thereby enabling highly scalable tunneling devices for superconductor-based quantum electronics.

preprint2019arXiv

Phonon and Thermal Properties of Quasi-Two-Dimensional FePS3 and MnPS3 Antiferromagnetic Semiconductor Materials

We report results of investigation of the phonon and thermal properties of the exfoliated films of layered single crystals of antiferromagnetic FePS3 and MnPS3 semiconductors. The Raman spectroscopy was conducted using three different excitation lasers with the wavelengths of 325 nm (UV), 488 nm (blue), and 633 nm (red). The resonant UV-Raman spectroscopy reveals new spectral features, which are not detectable via visible Raman light scattering. The thermal conductivity of FePS3 and MnPS3 thin films was measured by two different techniques: the steady-state Raman optothermal and transient time-resolved magneto-optical Kerr effect. The Raman optothermal measurements provided the orientation-average thermal conductivity of FePS3 to be 1.35 W/mK at room temperature. The transient measurements revealed that the through-plane and in-plane thermal conductivity of FePS3 is 0.85 W/mK and 2.7 W/mK, respectively. The films of MnPS3 have higher thermal conductivity of 1.1 W/mK through-plane and 6.3 W/mK in-plane. The data obtained by both techniques reveal strong thermal anisotropy of the films and the dominant contribution of phonons to heat conduction. Our results are important for the proposed applications of the antiferromagnetic semiconductor thin films in spintronic devices.

preprint2016arXiv

An Integrated Tantalum Sulfide - Boron Nitride - Graphene Oscillator: A Charge-Density-Wave Device Operating at Room Temperature

The charge-density-wave (CDW) phase is a macroscopic quantum state consisting of a periodic modulation of the electronic charge density accompanied by a periodic distortion of the atomic lattice in quasi-1D or layered 2D metallic crystals. Several layered transition metal dichalcogenides, such as 1T-TaSe2, 1T-TaS2 and 1T-TiSe2, exhibit unusually high transition temperatures to different CDW symmetry-reducing phases. These transitions can be affected by environmental conditions, film thickness and applied electric bias. However, device applications of these intriguing systems at room temperature or their integration with other 2D materials have not been explored. Here we show that in 2D CDW 1T-TaS2, the abrupt change in the electrical conductivity and hysteresis at the transition point between nearly-commensurate and incommensurate charge-density-wave phases can be used for constructing an oscillator that operates at room temperature. The hexagonal boron nitride was capped on 1T-TaS2 thin film to provide protection from oxidation, and an integrated graphene transistor provides a voltage tunable, matched, low-resistance load enabling precise voltage control of the oscillator frequency. The integration of these three disparate two-dimensional materials, in a way that exploits the unique properties of each, yields a simple, miniaturized, voltage-controlled oscillator device. Theoretical considerations suggest that the upper limit of oscillation frequency to be in the THz regime.

preprint2016arXiv

Topological Charge Analysis of Ultrafast Single Skyrmion Creation

Magnetic skyrmions are topologically non-trivial spin textures of potential interest for future information storage applications, and for such purposes, the control and understanding of single skyrmion creation is required. A scheme is analyzed to create single Néel-type and Bloch-type skyrmions in helimagnetic thin films utilizing the dynamical excitations induced by the Oersted field and the spin transfer torque given by a vertically injected spin-polarized current. A topological charge analysis using a lattice version of the topological charge provides insight into the locally triggered transition from a trivial to a non-trivial topological spin texture of the Néel or Bloch type skyrmion. The topological protection of the magnetic skyrmion is determined by the symmetric Heisenberg exchange energy. The critical switching current density is $\sim10^{7}\thinspace\textrm{A/cm}^{2}$, which decreases with the easy-plane type uniaxial anisotropy and thermal fluctuations. In-plane spin polarization of the injected current performs better than out-of-plane polarization, and it provides ultrafast switching times (within 100 ps) and reliable switching outcomes.

preprint2014arXiv

Electronic and Thermoelectric Properties of Few-Layer Transition Metal Dichalcogenides

The electronic and thermoelectric properties of one to four monolayers of MoS$_{2}$, MoSe$_{2}$, WS$_{2}$, and WSe$_{2}$ are calculated. For few layer thicknesses,the near degeneracies of the conduction band $K$ and $Σ$ valleys and the valence band $Γ$ and $K$ valleys enhance the n-type and p-type thermoelectric performance. The interlayer hybridization and energy level splitting determine how the number of modes within $k_BT$ of a valley minimum changes with layer thickness. In all cases, the maximum ZT coincides with the greatest near-degeneracy within $k_BT$ of the band edge that results in the sharpest turn-on of the density of modes. The thickness at which this maximum occurs is, in general, not a monolayer. The transition from few layers to bulk is discussed. Effective masses, energy gaps, power-factors, and ZT values are tabulated for all materials and layer thicknesses.

preprint2014arXiv

Gate Tunable Quantum Oscillations in Air-Stable and High Mobility Few-Layer Phosphorene Heterostructures

As the only non-carbon elemental layered allotrope, few-layer black phosphorus or phosphorene has emerged as a novel two-dimensional (2D) semiconductor with both high bulk mobility and a band gap. Here we report fabrication and transport measurements of phosphorene-hexagonal BN (hBN) heterostructures with one-dimensional (1D) edge contacts. These transistors are stable in ambient conditions for >300 hours, and display ambipolar behavior, a gate-dependent metal-insulator transition, and mobility up to 4000 $cm^2$/Vs. At low temperatures, we observe gate-tunable Shubnikov de Haas (SdH) magneto-oscillations and Zeeman splitting in magnetic field with an estimated g-factor ~2. The cyclotron mass of few-layer phosphorene holes is determined to increase from 0.25 to 0.31 $m_e$ as the Fermi level moves towards the valence band edge. Our results underscore the potential of few-layer phosphorene (FLP) as both a platform for novel 2D physics and an electronic material for semiconductor applications.

preprint2014arXiv

Mexican Hat and Rashba Bands in Few-Layer van der Waals Materials

The valence band of a variety of few-layer, two-dimensional materials consists of a ring of states in the Brillouin zone. The energy-momentum relation has the form of a `Mexican hat' or a Rashba dispersion. The two-dimensional density of states is singular at or near the band edge, and the band-edge density of modes turns on nearly abruptly as a step function. The large band-edge density of modes enhances the Seebeck coefficient, the power factor, and the thermoelectric figure of merit ZT. Electronic and thermoelectric properties are determined from ab initio calculations for few-layer III-VI materials GaS, GaSe, InS, InSe, for Bi$_{2}$Se$_{3}$, for monolayer Bi, and for bilayer graphene as a function of vertical field. The effect of interlayer coupling on these properties in few-layer III-VI materials and Bi$_{2}$Se$_{3}$ is described. Analytical models provide insight into the layer dependent trends that are relatively consistent for all of these few-layer materials. Vertically biased bilayer graphene could serve as an experimental test-bed for measuring these effects.

preprint2013arXiv

Graphene-Based Non-Boolean Logic Circuits

Graphene revealed a number of unique properties beneficial for electronics. However, graphene does not have an energy band-gap, which presents a serious hurdle for its applications in digital logic gates. The efforts to induce a band-gap in graphene via quantum confinement or surface functionalization have not resulted in a breakthrough. Here we show that the negative differential resistance experimentally observed in graphene field-effect transistors of "conventional" design allows for construction of viable non-Boolean computational architectures with the gap-less graphene. The negative differential resistance - observed under certain biasing schemes - is an intrinsic property of graphene resulting from its symmetric band structure. Our atomistic modeling shows that the negative differential resistance appears not only in the drift-diffusion regime but also in the ballistic regime at the nanometer-scale - although the physics changes. The obtained results present a conceptual change in graphene research and indicate an alternative route for graphene's applications in information processing.

preprint2012arXiv

Charge Density Waves in Exfoliated Thin Films of Van der Waals Materials

A number of the charge-density-wave materials reveal a transition to the macroscopic quantum state around 200 K. We used graphene-like mechanical exfoliation of titanium diselenide crystals to prepare a set of films with different thicknesses. The transition temperature to the charge-density-wave state was determined via modification of Raman spectra of titanium diselenide films. It was established that the transition temperature can increase from its bulk value to ~240 K as the thickness of the van-der-Waals films reduces to the nanometer range. The obtained results are important for the proposed applications of such materials in the collective-state information processing, which require room-temperature operation.

preprint2008arXiv

Conductance of a Conjugated Molecule with Carbon Nanotube Contacts

Calculations of the conductance of a carbon nanotube (CNT)-molecule-CNT structure are in agreement with experimental measurements [1]. The features in the transmission correspond directly to the features of the isolated molecular orbitals. The HOMO provides conductance at low bias that is relatively insensitive to the end groups of the cut CNTs, the cut angle, or the number of molecular bridges. A molecular conformation change not directly in the path of the carrier transport increases the resistance by over 2 orders of magnitude. [1] X. Guo, J. P. Small, J. E. Klare, Y. Wang, M. S. Purewal, I. W. Tam, B. H. Hong, R. Caldwell, L. Huang, S. O'Brien, et al., Science 311, 356 (2006), URL http://www.sciencemag.org/cgi/content/abstract/311/5759/356

Roger K. Lake

What is connected

Connect this record

See the researcher in context

Building this map preview

19 published item(s)

A Quieter State of Charge -- Ultra-Low-Noise Collective Current in Charge-Density-Wave Nanowires

Structural tuning magnetism and topology in a magnetic topological insulator

One-Dimensional van der Waals Quantum Materials -- State of the Art and Perspectives

Tuning Spin Transport in a Graphene Antiferromagnetic Insulator

Effects of filling, strain, and electric field on the Néel vector in antiferromagnetic CrSb

Electron transport through antiferromagnetic spin textures and skyrmions in a magnetic tunnel junction

Interfacial Dzyaloshinskii-Moriya Interaction of Antiferromagnetic Materials

Large spin-Hall effect in Si at room temperature

Properties of Shape-Engineered Phoxonic Crystals: Brillouin-Mandelstam Spectroscopy and Ellipsometry Study

Strain controlled superconductivity in few-layer NbSe2

Phonon and Thermal Properties of Quasi-Two-Dimensional FePS3 and MnPS3 Antiferromagnetic Semiconductor Materials

An Integrated Tantalum Sulfide - Boron Nitride - Graphene Oscillator: A Charge-Density-Wave Device Operating at Room Temperature

Topological Charge Analysis of Ultrafast Single Skyrmion Creation

Electronic and Thermoelectric Properties of Few-Layer Transition Metal Dichalcogenides

Gate Tunable Quantum Oscillations in Air-Stable and High Mobility Few-Layer Phosphorene Heterostructures

Mexican Hat and Rashba Bands in Few-Layer van der Waals Materials

Graphene-Based Non-Boolean Logic Circuits

Charge Density Waves in Exfoliated Thin Films of Van der Waals Materials

Conductance of a Conjugated Molecule with Carbon Nanotube Contacts