Source author record

Joel Chevrier

Joel Chevrier appears in the imported research catalog. Authorship, coauthor and topic links are available while profile ownership is still unclaimed.

ResearcherUnclaimed source record

Catalog footprint

What is connected

10works
8topics
4close collaborators

Actions

Connect this record

Log in to claim

Research graph

See the researcher in context

Open full explorer

Inspect adjacent papers, topics, institutions and collaborators without losing the researcher page.

Building this map preview

BZPEER is loading the nearby papers, people, topics and institutions for this page.

Published work

10 published item(s)

preprint2016arXiv

Frequency dependent visco-elastic properties of a water nanomeniscus : an AFM study in Force Feedback Mode

Recently, using an Atomic Force Microscope and a single cantilever excited at different frequencies it was shown that water nanomeniscus can exhibit a transition in mechanical responses when submitted to stimuli above few tens of kHz. The use of a single cantilever to explore phenomena at frequencies far from the cantilever resonance frequency is not a common and well-established strategy, and because water meniscus are ubiquitous in nature, we have also studied the water meniscus mechanical response, the stiffness G' (N/m) and the dissipation G"(kg/s), as a function of frequency by using cantilevers with different resonance frequencies. These results, based on classic dynamical AFM technics, confirm the anomalous mechanical response of water nanomeniscus when stimulated at frequencies high enough.

preprint2015arXiv

Out of equilibrium anomalous elastic response of a water nano-meniscus

We report the observation of a transition in the dynamical properties of water nano-menicus which dramatically change when probed at different time scales. Using a AFM mode that we name Force Feedback Microscopy, we observe this change in the simultaneous measurements, at different frequencies, of the stiffness G'(N/m), the dissipative coefficient G''(kg/sec) together with the static force. At low frequency we observe a negative stiffness as expected for capillary forces. As the measuring time approaches the microsecond, the dynamic response exhibits a transition toward a very large positive stiffness. When evaporation and condensation gradually lose efficiency, the contact line progressively becomes immobile. This transition is essentially controlled by variations of Laplace pressure.

preprint2015arXiv

Proximity effect on hydrodynamic interaction between a sphere and a plane measured by Force Feedback Microscopy at different frequencies

In this article, we measure the viscous damping $G'',$ and the associated stiffness $G',$ of a liquid flow in sphere-plane geometry in a large frequency range. In this regime, the lubrication approximation is expected to dominate. We first measure the static force applied to the tip. This is made possible thanks to a force feedback method. Adding a sub-nanometer oscillation of the tip, we obtain the dynamic part of the interaction with solely the knowledge of the lever properties in the experimental context using a linear transformation of the amplitude and phase change. Using a Force Feedback Microscope (FFM)we are then able to measure simultaneously the static force, the stiffness and the dissipative part of the interaction in a broad frequency range using a single AFM probe. Similar measurements have been performed by the Surface Force Apparatus with a probe radius hundred times bigger. In this context the FFM can be called nano-SFA.

preprint2013arXiv

Imaging material properties of biological samples with a Force Feedback Microscope

Mechanical properties of biological samples have been imaged with a \textit{Force Feedback Microscope}. Force, force gradient and dissipation are measured simultaneously and quantitatively, merely knowing the AFM cantilever spring constant. Our first results demonstrate that this robust method provides quantitative high resolution force measurements of the interaction The little oscillation imposed to the cantilever and the small value of its stiffness result in a vibrational energy much smaller than the thermal energy, reducing the interaction with the sample to a minimum. We show that the observed mechanical properties of the sample depend on the force applied by the tip and consequently on the sample indentation. Moreover, the frequency of the excitation imposed to the cantilever can be chosen arbitrarily, opening the way to frequency-dependent studies in biomechanics, sort of spectroscopic AFM investigations.

preprint2013arXiv

System analysis of Force Feedback Microscopy

It was shown recently that the Force Feedback Microscope can avoid the jump-to-contact in Atomic force Microscopy even when the cantilevers used are very soft, thus increasing force resolution. In this letter, we explore theoretical aspects of the associated real time control of the tip position. We take into account lever parameters such as the lever characteristics in its environment, spring constant, mass, dissipation coefficient and the operating conditions such as controller gains, and interaction force. We show how the controller parameters are determined so that the FFM functions at its best and estimate the bandwidth of the system under these conditions.

preprint2012arXiv

Measurement of the complete interaction force curve at the nanoscale

The force between two interacting particles as a function of distance is one of the most fundamental curves in science. In this regard, Atomic Force Microscopy (AFM) represents the most powerful tool in nanoscience but with severe limits when it is to probe attractive interactions with high sensitivity. The Force Feedback Microscope (FFM) described here, removes from AFM the well known jump to contact problem that precludes the complete exploration of the interaction curve and the study of associated energy exchanges. The FFM makes it possible to explore tip-surface interactions in the entire range of distances with a sensitivity better than 1 pN. FFM stands out as a radical change in AFM control paradigms. With a surprisingly simple arrangement it is possible to provide the AFM tip with the right counterforce to keep it fixed at any time. The counterforce is consequently equal to the tip-sample force. The force, force gradient and damping are simultaneously measured independently of the tip position. This permits the measurement of energy transfer in thermodynamic transformations. Here we show some FFM measurement examples of the complete interaction force curve and in particular that the FFM can follow the nucleation of a water bridge by measuring the capillary attractive force at all distances, without jump to contact despite the large attractive capillary force. Real time combination of the measured parameters will lead to new imaging modalities with chemical contrast in different environments.

preprint2012arXiv

Teaching Classical Mechanics using Smartphones

Using a personal computer and a smartphone, iMecaProf is a software that provides a complete teaching environment for practicals associated to a Classical Mechanics course. iMecaProf proposes a visual, real time and interactive representation of data transmitted by a smartphone using the formalism of Classical Mechanics. Using smartphones is more than using a set of sensors. iMecaProf shows students that important concepts of physics they here learn, are necessary to control daily life smartphone operations. This is practical introduction to mechanical microsensors that are nowadays a key technology in advanced trajectory control. First version of iMecaProf can be freely downloaded. It will be tested this academic year in Université Joseph Fourier (Grenoble, France)

preprint2011arXiv

Emissivity measurements with an Atomic Force Microscope

We show that functionalized micromechanical bilayer levers can be used as sensitive probes to accurately measure radiative heat flux in vacuum between two materials at the micro scale. By means of calibration to one material these measurements can be made quantitative for radiative heat flux or for either temperature or material emissivity. We discuss issues and opportunities for our method and provide ample technical details regarding its implementation and demonstrate good correspondence with the Stefan Boltzman law. We use this system to probe the phase transition of VO2 and find that radiative heat transfer in farfield between VO2 and glass can be reversibly modulated by a factor of 5.

preprint2011arXiv

How to display science since images have no mass

Education, science, in fact the whole society, extensively use images. Between us and the world are the visual displays. Screens, small and large, individual or not, are everywhere. Images are increasingly the 2D substrate of our virtual interaction with reality. However images will never support a complete representation of the reality. Three-dimensional representations will not change that. Images are primarily a spatial representation of our world dedicated to our sight. Key aspects such as energy and the associated forces are not spatially materialized. In classical physics, interaction description is based on Newton equations with trajectory and force as the dual central concepts. Images can in real time show all aspects of trajectories but not the associated dynamical aspects described by forces and energies. Contrary to the real world, the world of images opposes no constrain, nor resistance to our actions. Only the physical quantities, that do not contain mass in their dimension can be satisfactory represented by images. Often symbols such as arrows are introduced to visualize the force vectors.

preprint2010arXiv

Can nanotechnology experimentally solve the plane-plane challenge

Non-contact interaction between two parallel flat surfaces is a central paradigm in sciences. This situation is the starting point for a wealth of different models: the capacitor description in electrostatics, hydrodynamic flow, thermal exchange, the Casimir force, direct contact study, third body confinement such as liquids or films of soft condensed matter. The control of parallelism is so demanding that no versatile single force machine in this geometry has been proposed so far. Using a combination of nanopositioning based on inertial motors and microcrystal shaping with Focused Ion Beams (FIB) we propose here an experimental set up that should enable one to measure interactions between movable surfaces separated by gaps in the micrometer and the nanometer ranges.