Source author record

A. Wagenpfahl

A. Wagenpfahl appears in the imported research catalog. Authorship, coauthor and topic links are available while profile ownership is still unclaimed.

ResearcherUnclaimed source record

Catalog footprint

What is connected

6works
1topics
4close collaborators

Actions

Connect this record

Log in to claim

Research graph

See the researcher in context

Open full explorer

Inspect adjacent papers, topics, institutions and collaborators without losing the researcher page.

Building this map preview

BZPEER is loading the nearby papers, people, topics and institutions for this page.

Published work

6 published item(s)

preprint2010arXiv

Comment on "Interface state recombination in organic solar cells"

In a recent paper, Street et al. [Phys. Rev. B 81, 205307 (2010)] propose first order recombination due to interface states to be the dominant loss mechanism in organic bulk heterojunction solar cells, based on steady-state current--voltage characteristics. By applying macroscopic simulations, we found that under typical solar cell conditions, monomolecular or bimolecular recombination cannot be inferred from the slope of the light intensity dependent photocurrent. In addition, we discuss the validity of calculating a mobility--lifetime product from steady-state measurements. We conclude that the experimental technique applied by Street et al. is not sufficient to unambiguously determine the loss mechanism.

preprint2010arXiv

Investigation of the Photocurrent in Bulk Heterojunction Solar Cells

We investigated the photocurrent in poly(3-hexylthiophene-2,5-diyl) (P3HT):[6,6]-phenyl-C$_{61}$ butyric acid methyl ester (PCBM) solar cells by applying a pulsed measurement technique. For annealed samples, a point of optimal symmetry (POS) with a corresponding voltage $V_\text{POS}$ of 0.52--0.64 V could be determined. Based on macroscopic simulations and results from capacitance--voltage measurements, we identify this voltage with flat band conditions in the bulk of the cell, but not the built-in voltage as proposed by [Ooi et al., J. Mater. Chem. 18 (2008) 1644]. We calculated the field dependent polaron pair dissociation after Onsager--Braun and the voltage dependent extraction of charge carriers after Sokel and Hughes with respect to this point of symmetry. Our analysis allows to explain the experimental photocurrent in both forward and reverse directions. Also, we observed a voltage--independent offset of the photocurrent. As this offset is crucial for the device performance, we investigated its dependence on cathode material and thermal treatment. From our considerations we gain new insight into the photocurrent`s voltage dependence and the limitations of device efficiency.

preprint2010arXiv

Organic solar cell efficiencies under the aspect of reduced surface recombination velocities

The charge carrier mobility is a key parameter for the organic bulk heterojunction solar cell efficiency. It was recently shown that the interplay charge carrier transport and recombination, both depending on electron and hole mobilities, leads to a point of maximum power conversion efficiency at a finite mobility. Changes of bulk and surface recombination rate, however, can strongly influence this behavior. These processes were previously not considered adequately, as surface recombination velocities of infinity were implicitly assumed or bulk recombination parameters not discussed in detail. In this manuscript, using a macroscopic effective medium simulation, we consider how a reduced bulk recombination process in combination with finite surface recombination velocities affect the power conversion efficiency. Instead of a maximum efficiency at a specific charge carrier mobility, we show that with realistic assumptions and passivated surfaces the efficiency is increased further, saturating only at higher mobilities. Thus, a mobility optimisation is more important for the solar cell performance then previously shown.

preprint2010arXiv

S-shaped current-voltage characteristics of organic solar devices

Measuring the current-voltage characteristic of organic bulk heterojunction solar devices sometimes reveals an s-shaped deformation. We qualitatively produce this behaviour by a numerical device simulation assuming a reduced surface recombination. Furthermore we show how to experimentally create these double diodes by applying an oxygen plasma etch on the indium tin oxide (ITO) anode. Restricted charge transport over material interfaces accumulates space charges and therefore creates s-shaped deformations. Finally we discuss the consequences of our findings for the open circuit voltage $V_{oc}$

preprint2009arXiv

Polaron Recombination in Pristine and Annealed Bulk Heterojunction Solar Cells

The major loss mechanism of photogenerated polarons was investigated in P3HT:PCBM solar cells by the photo-CELIV technique. For pristine and annealed devices, we find that the experimental data can be explained by a bimolecular recombination rate reduced by a factor of about ten (pristine) and 25 (annealed) as compared to Langevin theory. Aided by a macroscopic device model, we discuss the implications of the lowered loss rate on the characteristics of polymer:fullerene solar cells.

preprint2008arXiv

Influence of Charge Carrier Mobility on the Performance of Organic Solar Cells

The power conversion efficiency of organic solar cells based on donor--acceptor blends is governed by an interplay of polaron pair dissociation and bimolecular polaron recombination. Both processes are strongly dependent on the charge carrier mobility, the dissociation increasing with faster charge transport, with raised recombination losses at the same time. Using a macroscopic effective medium simulation, we calculate the optimum charge carrier mobility for the highest power conversion efficiency, for the first time accounting for injection barriers and a reduced Langevin-type recombination. An enhancement of the charge carrier mobility from $10^{-8}$m$^2$/Vs for state of the art polymer:fullerene solar cells to about $10^{-6}$m$^2$/Vs, which yields the maximum efficiency, corresponds to an improvement of only about 20% for the given parameter set.