BZPEERPapers, people, evidence and research pathsDiscover
Research tools
Network
Opportunities
Account
Source author record
E. Goldobin appears in the imported research catalog. Authorship, coauthor and topic links are available while profile ownership is still unclaimed.
Catalog footprint
Research graph
Inspect adjacent papers, topics, institutions and collaborators without losing the researcher page.
BZPEER is loading the nearby papers, people, topics and institutions for this page.
Published work
We propose simple models for the current-voltage characteristics of typical Josephson ratchets. We consider the case of a ratchet working against a constant applied counter force and derive analytical expressions for the key characteristics of such a ratchet: rectification curve, stopping force, input and output powers and rectification efficiency. Optimization of the ratchet performance is discussed.
We demonstrate experimentally the operation of a deterministic Josephson ratchet with tunable asymmetry. The ratchet is based on a $φ$ Josephson junction with a ferromagnetic barrier operating in the underdamped regime. The system is probed also under the action of an additional dc current, which acts as a counter force trying to stop the ratchet. Under these conditions the ratchet works against the counter force, thus producing a non-zero output power. Finally, we estimate the efficiency of the $φ$ Josephson junction ratchet.
We consider a short Josephson junction with a phase discontinuity $κ$ created, e.g., by a pair of tiny current injectors, at some point $x_0$ along the length of the junction. We derive the effective current-phase relation (CPR) for the system as a whole, i.e., reduce it to an effective point-like junction. From the effective CPR we obtain the ground state of the system and predict the dependence of its critical current on $κ$. We show that in a large range of $κ$ values the effective junction behaves as a $φ_0$ Josephson junction, i.e., has a unique ground state phase $φ_0$ within each $2π$ interval. For $κ\approxπ$ and $x_0$ near the middle of the junction one obtains a $φ_0\pmφ$ junction, i.e., the Josephson junction with degenerate ground state phase $φ_0\pmφ$ within each $2π$ interval. Further, in view of possible escape experiments especially in the quantum domain, we investigate the scaling of the energy barrier and eigenfrequency close to the critical currents and predict the behavior of the escape histogram width $σ(κ)$ in the regime of the macroscopic quantum tunneling.
We used one-dimensional coupled sine-Gordon equations combined with heat diffusion equations to numerically investigate the thermal and electromagnetic properties of a $300\,μ\mathrm{m}$ long intrinsic Josephson junction stack consisting of $N = 700$ junctions. The junctions in the stack are combined to $M$ segments where we assume that inside a segment all junctions behave identically. Most simulations are for $M = 20$. For not too high bath temperatures there is the appearence of a hot spot at high bias currents. In terms of electromagnetic properties, robust standing wave patterns appear in the current density and electric field distributions. These patterns come together with vortex/antivortex lines across the stack that correspond to $π$ kink states, discussed before in the literature for a homogeneous temperature distribution in the stack. We also discuss scaling of the thermal and electromagnetic properties with $M$, on the basis of simulations with $M$ between 10 and 350.
We study a 0-$π$ dc superconducting quantum interference device (SQUID) with asymmetric inductances and critical currents of the two Josephson junctions (JJs). By considering such a dc SQUID as a black box with two terminals, we calculate its effective current-phase relation $I_s(ψ)$ and the Josephson energy $U(ψ)$, where $ψ$ is the Josephson phase across the terminals. We show that there is a domain of parameters where the black box has the properties of a $φ$ JJ with degenerate ground state phases $ψ=\pmφ$. The $φ$ domain is rather large, so one can easily construct a $φ$ JJ experimentally. We derive the current phase relation and show that it can be tuned \emph{in situ} by applying an external magnetic flux resulting in a continuous transition between the systems with static solutions $ψ=\pmφ$, $ψ=φ_0$ ($φ_0 \neq 0,π$) and even $ψ=φ_0\pmφ$. The dependence of $φ_0$ on applied magnetic flux is not $2π$ (one flux quantum) periodic.
Using the Usadel equation approach, we provide a compact formalism to calculate the critical current density of 21 different types of ferromagnetic (F) Josephson junctions containing insulating (I) and normal metal (N) layers in the weak link regions. In particular, we obtain that even a thin additional N layer may shift the 0-$π$ transitions to larger or smaller values of the thickness $d_F$ of the ferromagnet, depending on its conducting properties. For certain values of $d_F$, a 0-$π$ transition can even be achieved by changing only the N layer thickness. We use our model to fit experimental data of SIFS and SINFS tunnel junctions, where S is a superconducting electrode.
We propose a tunable macroscopic quantum system based on two fractional vortices. Our analysis shows that two coupled fractional vortices pinned at two artificially created κ discontinuities of the Josephson phase in a long Josephson junction can reach the quantum regime where coherent quantum oscillations arise. For this purpose we map the dynamics of this system to that of a single particle in a double-well potential. By tuning the κ discontinuities with injector currents we are able to control the parameters of the effective double-well potential as well as to prepare a desired state of the fractional vortex molecule. The values of the parameters derived from this model suggest that an experimental realisation of this tunable macroscopic quantum system is possible with today's technology.
We calculate the current phase relation of a planar Josephson junction with a ferromagnetic weak link located on top of a thin normal metal film. Following experimental observations we assume transparent superconductor-ferromagnet interfaces. This provides the best interlayer coupling and a low suppression of the superconducting correlations penetrating from the superconducting electrodes into the ferromagnetic layer. We show that this Josephson junction is a promising candidate for an experimental ϕ junction realization.
We consider an infinitely long 0-$π$ Josephson junction consisting of 0 and $π$ regions having different critical current densities $j_{c,0}$ and $j_{c,π}$. The ground state of such a junction corresponds to a spontaneosly formed asymmetric semifluxon with tails decaying on different length scales. We calculate the depinning current of such a fractional vortex and show that it is different for positive and negative bias polarity. We also show that upon application of a bias current, the fractional flux (topological charge) associated with the vortex changes. We calculate the range of fractional flux associated with the vortex when the bias changes from negative to positive critical (depinning) values.
The $φ$ Josephson junction has a doubly degenerate ground state with the Josephson phases $\pmφ$. We demonstrate the use of such a $φ$ Josephson junction as a memory cell (classical bit), where writing is done by applying a magnetic field and reading by applying a bias current. In the "store" state, the junction does not require any bias or magnetic field, but just needs to stay cooled for permanent storage of the logical bit. Straightforward integration with Rapid Single Flux Quantum logic is possible.
We consider a $φ$ Josephson junction, which has a bistable zero-voltage state with the stationary phases $ψ=\pmφ$. In the non-zero voltage state the phase "moves" viscously along a tilted periodic double-well potential. When the tilting is reduced quasistatically, the phase is retrapped in one of the potential wells. We study the viscous phase dynamics to determine in which well ($-φ$ or $+φ$) the phase is retrapped for a given damping, when the junction returns from the finite-voltage state back to zero-voltage state. In the limit of low damping the $φ$ Josephson junction exhibits a butterfly effect --- extreme sensitivity of the destination well on damping. This leads to an impossibility to predict the destination well.
We demonstrate a high-frequency generator operating at ~200GHz based on flipping a semifluxon in a Josephson junction of moderate normalized length. The semifluxon spontaneously appears at the $π$ discontinuity of the Josephson phase artificially created by means of two tiny current injectors. The radiation is detected by an on-chip detector (tunnel junction). The estimated radiation power (at the detector) is ~8nW and should be compared with the dc power of ~100nW consumed by the generator. The measured radiation linewidth, as low as 1.1MHz, is typical for geometrical (Fiske) resonances although we tried to suppress such resonances by placing well-matched microwave transformers at its both ends. Making use of a phase-locking feedback loop we are able to reduce the radiation linewidth to less than 1Hz measured relative to the reference oscillator and defined just by the resolution of our measurement setup.
We demonstrate experimentally the existence of Josephson junctions having a doubly degenerate ground state with an average Josephson phase ψ=\pmϕ. The value of ϕ can be chosen by design in the interval 0<ϕ<π. The junctions used in our experiments are fabricated as 0-π Josephson junctions of moderate normalized length with asymmetric 0 and π regions. We show that (a) these ϕ Josephson junctions have two critical currents, corresponding to the escape of the phase ψ from -ϕ and +ϕ states; (b) the phase ψ can be set to a particular state by tuning an external magnetic field or (c) by using a proper bias current sweep sequence. The experimental observations are in agreement with previous theoretical predictions.
We consider a 0-$π$ Josephson junction consisting of asymmetric 0 and $π$ regions of different lengths $L_0$ and $L_π$ having different critical current densities $j_{c,0}$ and $j_{c,π}$. If both segments are rather short, the whole junction can be described by an \emph{effective} current-phase relation for the spatially averaged phase $ψ$, which includes the usual term $\propto\sin(ψ)$, a \emph{negative} second harmonic term $\propto\sin(2ψ)$ as well as the unusual term $\propto H \cosψ$ tunable by magnetic field $H$. Thus one obtains an electronically tunable current-phase relation. At H=0 this corresponds to the $φ$ Josephson junction.
We study the critical current I_c dependence on applied magnetic field H for multifacet YBa_2Cu_3O_{7-δ}-Au-Nb ramp-type zigzag Josephson junctions. For many experiments one would like to apply a homogeneous field in the junction plane. However, even tiny misalignments can cause drastic deviations from homogeneity. We show this explicitly by measuring and analyzing I_c vs. H for an 8 facet junction, forming an array of 4\times(0-π)-segments. The ramp angle is θ_r=8^\circ. The facet width is 10\,\mum. H is applied under different angles θrelative to the substrate plane and different angles ϕrelative to the in-plane orientation of the zigzags. We find that a homogeneous flux distribution is only achieved for an angle θ_h\approx 1^\circ - 2^\circ and that even a small misalignment \sim 0.1^\circ relative to θ_h can cause a substantial inhomogeneity of the flux density inside the junction, drastically altering its I_c vs. H interference pattern. We also show, that there is a dead angle θ^*_d relative to θ_h of similar magnitude, where the average flux density completely vanishes.
For high-performance superconducting quantum devices based on Josephson junctions (JJs) decreasing lateral sizes is of great importance. Fabrication of sub-μm JJs is challenging due to non-flat surfaces with step heights of up to several 100 nm generated during the fabrication process. We have refined a fabrication process with significantly decreased film thicknesses, resulting in almost flat surfaces at intermediate steps during the JJ definition. In combination with a mix-&-match process, combining electron-beam lithography (EBL) and conventional photolithography, we can fabricate JJs with lateral dimensions down to 0.023 μm^2. We propose this refined process as an alternative to the commonly used chemical-mechanical polishing (CMP) procedure. We present transport measurements of JJs at 4.2 K that yield critical-current densities in the range from 50 to 10^4 A/cm^2. Our JJ process yields excellent quality parameters, Rsg/Rn up to ~50 and Vgap up to 2.81 mV, and also allows the fabrication of high-quality sub-μm wide long JJs (LJJs) for the study of Josephson vortex behavior. The developed technique can also be used for similar multilayer processes and is very promising for fabricating sub-μm JJs for quantum devices such as SQUIDs, qubits and SIS mixers.
We propose to create pairs of semifluxons starting from a flat-phase state in long, optical 0-pi-0 Josephson junctions formed with internal electronic states of atomic Bose-Einstein condensates. In this optical system, we can dynamically tune the length of the pi-junction, the detuning of the optical transition, or the strength of the laser-coupling, to induce transitions from the flat-phase state to such a semifluxon-pair state. Similarly as in superconducting 0-pi-0 junctions, there are two, energetically degenerate semifluxon-pair states. A linear mean-field model with two internal electronic states explains this degeneracy and shows the distinct static field configuration in a phase-diagram of the junction parameters. This optical system offers the possibility to dynamically create a coherent superposition of the distinct semifluxon-pair states and observe macroscopic quantum oscillation.
We investigate experimentally a deterministic underdamped Josephson vortex ratchet -- a fluxon-particle moving along a Josephson junction in an asymmetric periodic potential. By applying a sinusoidal driving current one can compel the vortex to move in a certain direction, producing average dc voltage across the junction. Being in such a rectification regime we also load the ratchet, i.e., apply an additional dc bias current I_dc (counterforce) which tilts the potential so that the fluxon climbs uphill due to the ratchet effect. The value of the bias current at which the fluxon stops climbing up defines the strength of the ratchet effect and is determined experimentally. This allows us to estimate the loading capability of the ratchet, the output power and efficiency. For the quasi-static regime we present a simple model which delivers simple analytic expressions for the above mentioned figures of merit.
We consider an asymmetric 0-pi Josephson junction consisting of 0 and pi regions of different lengths L_0 and L_pi. As predicted earlier this system can be described by an effective sine-Gordon equation for the spatially averaged phase psi so that the effective current-phase relation of this system includes a \emph{negative} second harmonic ~sin(2 psi). If its amplitude is large enough, the ground state of the junction is doubly degenerate psi=\pmvarphi, where varphi depends on the amplitudes of the first and second harmonics. We study the behavior of such a junction in an applied magnetic field H and demonstrate that H induces an additional term ~H cos(psi) in the effective current-phase relation. This results in a non-trivial ground state \emph{tunable} by magnetic field. The dependence of the critical current on H allows for revealing the ground state experimentally.
In long Josephson junctions with multiple discontinuities of the Josephson phase, fractional vortex molecules are spontaneously formed. At each discontinuity point a fractional Josephson vortex carrying a magnetic flux $|Φ|<Φ_0$, $Φ_0\approx 2.07\times 10^{-15}$ Wb being the magnetic flux quantum, is pinned. Each vortex has an oscillatory eigenmode with a frequency that depends on $Φ/Φ_0$ and lies inside the plasma gap. We experimentally investigate the dependence of the eigenfrequencies of a two-vortex molecule on the distance between the vortices, on their topological charge $\wp=2πΦ/Φ_0$ and on the bias current $γ$ applied to the Josephson junction. We find that with decreasing distance between vortices, a splitting of the eigenfrequencies occurs, that corresponds to the emergence of collective oscillatory modes of both vortices. We use a resonant microwave spectroscopy technique and find good agreement between experimental results and theoretical predictions.
The proximity effect and the Josephson current in a superconductor-insulator-ferromagnet-superconductor (SIFS) junction are investigated within the framework of the quasiclassical Eilenberger equations. This investigation allows us to compare the dirty and the clean limits, to investigate an arbitrary impurity scattering, and to determine the applicability limits of the Usadel equations for such structures. The role of different types of the FS interface is analyzed. It is shown that the decay length and the spatial oscillation period of the Eilenberger function may exhibit a nonmonotonic dependence on the properties of the ferromagnetic layer such as exchange field or electron mean free path. The results of our calculations are applied to the interpretation of experimentally observed dependencies of the critical current density on the ferromagnet thickness in Josephson junctions containing a Ni layer with an arbitrary scattering.
We present the latest generation of superconductor-insulator-ferromagnet-superconductor Josephson tunnel junctions with a step-like thickness of the ferromagnetic (F) layer. The F-layer thicknesses $d_1$ and $d_2$ in both halves were varied to obtain different combinations of positive and negative critical current densities $j_{c,1}$ and $j_{c,2}$. The measured dependences of the critical current on applied magnetic field can be well described by a model which takes into account different critical current densities (obtained from reference junctions) and different net magnetization of the multidomain ferromagnetic layer in both halves.
We have realized multifacet Josephson junctions with periodically alternating critical current density (MJJs) using superconductor-insulator-ferromagnet-superconductor heterostructures. We show that anomalous features of critical current vs. applied magnetic field, observed also for other types of MJJs, are caused by a non-uniform flux density (parallel to the barrier) resulting from screening currents in the electrodes in the presence of a (parasitic) off-plane field component.
We present a detailed analysis of the dependence of the critical current I_c on the magnetic field B of 0, Pi, and 0-Pi superconductor-insulator-ferromagnet-superconductor Josephson junctions. I_c(B) of the 0 and Pi junction closely follows a Fraunhofer pattern, indicating a homogeneous critical current density j_c(x). The maximum of I_c(B) is slightly shifted along the field axis, pointing to a small remanent in-plane magnetization of the F-layer along the field axis. I_c(B) of the 0-Pi junction exhibits the characteristic central minimum. I_c however has a finite value here, due to an asymmetry of j_c in the 0 and Pi part. In addition, this I_c(B) exhibits asymmetric maxima and bumped minima. To explain these features in detail, flux penetration being different in the 0 part and the Pi part needs to be taken into account. We discuss this asymmetry in relation to the magnetic properties of the F-layer and the fabrication technique used to produce the 0-Pi junctions.
We propose a method to realize a $ϕ$ Josephson junction by combining alternating 0 and $π$ parts (sub junctions) with an intrinsically non-sinusoidal current-phase relation (CPR). Conditions for the realization of the $ϕ$ ground state are analyzed. It is shown that taking into account the non-sinusoidal CPR for a "clean junction with a ferromagnetic (F) barrier, one can significantly enlarge the domain (regime of suitable F-layer thicknesses) of the $ϕ$ ground state and make the practical realization of $ϕ$ Josephson junctions feasible. Such junctions may also have two different stable solutions, such as 0 and $π$, 0 and $ϕ$, or $ϕ$ and $π$.
Josephson junctions with ferromagnetic barrier can have positive or negative critical current depending on the thickness $d_F$ of the ferromagnetic layer. Accordingly, the Josephson phase in the ground state is equal to 0 (a conventional or 0 junction) or to $π$ ($π$ junction). When 0 and $π$ segments are joined to form a "0-$π$ junction", spontaneous supercurrents around the 0-$π$ boundary can appear. Here we report on the visualization of supercurrents in superconductor-insulator-ferromagnet-superconductor (SIFS) junctions by low-temperature scanning electron microscopy (LTSEM). We discuss data for rectangular 0, $π$, 0-$π$, 0-$π$-0 and 20 \times 0-$π$ junctions, disk-shaped junctions where the 0-$π$ boundary forms a ring, and an annular junction with two 0-$π$ boundaries. Within each 0 or $π$ segment the critical current density is fairly homogeneous, as indicated both by measurements of the magnetic field dependence of the critical current and by LTSEM. The $π$ parts have critical current densities $j_c^π$ up to $35\units{A/cm^2}$ at $T = 4.2\units{K}$, which is a record value for SIFS junctions with a NiCu F-layer so far. We also demonstrate that SIFS technology is capable to produce Josephson devices with a unique topology of the 0-$π$ boundary.
We consider a symmetric 0-pi Josephson junction of length $L$, which classically can be in one of two degenerate ground states up or down, corresponding to supercurrents circulating clockwise or counterclockwise around the 0-pi boundary. When the length $L$ of the junction becomes smaller than the Josephson penetration depth $λ_J$, the system can switch from one state to the other due to thermal fluctuations or quantum tunneling. We map this problem to the dynamics of a single particle in a periodic double well potential and estimate parameters for which macroscopic quantum coherence may be observed. We conclude that this system is not very promising to build a qubit because (a) it requires very low temperatures to reach the quantum regime, (b) its tiny flux is hard to read out and (c) it is very sensitive to the asymmetries between the 0 and pi parts of the junction.