Source author record

B. J. Reschovsky

B. J. Reschovsky appears in the imported research catalog. Authorship, coauthor and topic links are available while profile ownership is still unclaimed.

ResearcherUnclaimed source record

physics.atom-ph physics.ins-det cond-mat.quant-gas physics.optics

Catalog footprint

What is connected

5works

4topics

4close collaborators

Actions

Connect this record

Open graph Browse works

Inspect adjacent papers, topics, institutions and collaborators without losing the researcher page.

Building this map preview

BZPEER is loading the nearby papers, people, topics and institutions for this page.

preprint2022arXiv

Electro-optic frequency combs for rapid interrogation in cavity optomechanics

Electro-optic frequency combs were employed to rapidly interrogate an optomechanical sensor, demonstrating spectral resolution substantially exceeding that possible with a mode-locked frequency comb. Frequency combs were generated using an integrated-circuit-based direct digital synthesizer and utilized in a self-heterodyne configuration. Unlike approaches based upon laser locking or sweeping, the present approach allows rapid, parallel measurements of full optical cavity modes, large dynamic range of sensor displacement, and acquisition across a wide frequency range between DC and 500 kHz. In addition to being well suited to measurements of cavity optomechanical sensors, this optical frequency comb-based approach can be utilized for interrogation in a wide range of physical and chemical sensors.

preprint2022arXiv

High dynamic range electro-optic dual-comb interrogation of optomechanical sensors

An interleaved, chirped electro-optic dual comb system is demonstrated for rapid, high dynamic range measurements of cavity optomechanical sensors. This approach allows for the cavity displacements to be interrogated at measurement times as fast as 10 μs over ranges far larger than can be achieved with alternative methods. While the performance of this novel readout approach is evaluated with an optomechanical accelerometer, this method is applicable to a wide range of applications including temperature, pressure, and humidity sensing as well as acoustics and molecular spectroscopy.

preprint2016arXiv

A 3-photon process for producing a degenerate gas of metastable alkaline-earth atoms

We present a method for creating a quantum degenerate gas of metastable alkaline-earth atoms. This has yet to be achieved due to inelastic collisions that limit evaporative cooling in the metastable states. Quantum degenerate samples prepared in the $^{1}S_{0}$ ground state can be rapidly transferred to either the $^{3}P_{2}$ or $^{3}P_{0}$ state via a coherent 3-photon process. Numerical integration of the density matrix evolution for the fine structure of bosonic alkaline-earth atoms shows that transfer efficiencies of $\simeq90\%$ can be achieved with experimentally feasible laser parameters in both Sr and Yb. Importantly, the 3-photon process can be set up such that it imparts no net momentum to the degenerate gas during the excitation, which will allow for studies of metastable samples outside the Lamb-Dicke regime. We discuss several experimental challenges to successfully realizing our scheme, including the minimization of differential AC Stark shifts between the four states connected by the 3-photon transition.

preprint2016arXiv

An ultra-low noise, high-voltage piezo driver

We present an ultra-low noise, high-voltage driver suited for use with piezoelectric actuators and other low-current applications. The architecture uses a flyback switching regulator to generate up to 250V in our current design, with an output of 1 kV or more possible with small modifications. A high slew-rate op-amp suppresses the residual switching noise, yielding a total RMS noise of $\approx 100μ$V (1 Hz--100 kHz). A low-voltage ($\pm 10$V), high bandwidth signal can be summed with unity gain directly onto the output, making the driver well-suited for closed-loop feedback applications. Digital control enables both repeatable setpoints and sophisticated control logic, and the circuit consumes less than 150mA at $\pm 15$V.

preprint2015arXiv

Enhanced Magnetic Trap Loading for Atomic Strontium

We report on a technique to improve the continuous loading of atomic strontium into a magnetic trap from a Magneto-Optical Trap (MOT). This is achieved by adding a depumping laser tuned to the 3P1 to 3S1 (688-nm) transition. The depumping laser increases atom number in the magnetic trap and subsequent cooling stages by up to 65 % for the bosonic isotopes and up to 30 % for the fermionic isotope of strontium. We optimize this trap loading strategy with respect to the 688-nm laser detuning, intensity, and beam size. To understand the results, we develop a one-dimensional rate equation model of the system, which is in good agreement with the data. We discuss the use of other transitions in strontium for accelerated trap loading and the application of the technique to other alkaline-earth-like atoms.