Researcher profile

Ashish V. Orpe

Ashish V. Orpe contributes to research discovery and scholarly infrastructure.

ResearcherAffiliation not importedOpen to collaborate

cond-mat.soft

Trust snapshot

Quick read

Trust 17 - Baseline

4works

0followers

1topics

4close collaborators

Actions

Decide how to stay connected

Follow researcher0

Inspect adjacent work, topics, institutions and collaborators without jumping out to a separate graph page.

Building this graph slice

BZPEER is loading the nearby papers, people, topics and institutions for this page.

preprint2020arXiv

Microstructure and yielding of capillary force induced gel

We have investigated the rheology and structure of a gel formed from a mixture of non-Brownian particles and two immiscible liquids. The suspension of particles in a liquid undergoes gelation upon the addition of a small content of second, wetting liquid which forms liquid bridges between particles leading to a sample spanning network. The rheology of this gel primarily exhibits a yield stress at low shear rates followed by a linear variation of shear stress at high shear rates. The apparent yield stress extracted from the flow curves increases rapidly with volume fraction of second liquid before saturation, while it exhibits a monotonic increase with increasing particle concentration. Rescaling of the yield stress curves using suitable shift factors results in an empirical expression for the yield stress showing squared dependence on liquid fraction and a rapid increase with particle fraction above a certain value, both combined in a highly nonlinear manner. The microstructural variations with changing secondary liquid content and particle fractions are captured using three dimensional X-ray tomography technique. The microstructure is observed to show increased local compactness with increased liquid content and increased spatial homogeneity with increased particle fractions. The images from X-ray tomography are analysed to obtain the distributions of particle-particle bonds (coordination number) in the system which serve to explain the observed yield stress behavior in a qualitative manner.

preprint2016arXiv

Fingering instability of a suspension film spreading on a spinning disk

The spreading of a thin film of suspension on a spinning disk and the accompanying contact line instability is studied through flow visualization experiments. The critical radius for the onset of instability shows an increase with increase in the particle fraction ($ϕ_{p}$) before decreasing slightly at the highest value of $ϕ_{p}$ studied, while the instability wavelength ($λ$) exhibits a non-monotonic dependence. The value of $λ$ is close to that for a partially wetting liquid at lower $ϕ_{p}$, it decreases with increasing $ϕ_{p}$ to a minimum before increasing again at largest $ϕ_{p}$. The non-monotonic trends observed for $λ$ are discussed in light of the linear stability analysis of thin film equations derived for suspensions by Cook {\it et al.} [Linear stability of particle-laden thin films, Eur. Phys. J.: Spec. Top. {\bf 166}, 77 (2009)] and Balmforth {\it et al.} [Surface tension driven fingering of a viscoplastic film, J. Non Newtonian Fluid Mech. {\bf 142}, 143 (2007)].

preprint2014arXiv

Flow of granular matter in a silo with multiple exit orifices: Jamming to mixing

We investigate the mixing characteristics of dry granular material while draining down a silo with multiple exit orifices. The mixing in the silo, which otherwise consists of noninteracting stagnant and flow regions, is observed to improve significantly when the flow through specific orifices is stopped intermittently. This momentary stoppage of flow through the orifice is either controlled manually or is chosen by the system itself when the orifice width is small enough to cause spontaneous jamming and unjamming. We observe that the overall mixing behavior shows a systematic dependence on the frequency of closing and opening of specific orifices. In particular, the silo configuration employing random jamming and unjamming of any of the orifices shows early evidence of chaotic mixing. When operated in a multipass mode, the system exhibits a practical and efficient way of mixing particles.

preprint2005arXiv

Rheology of surface granular flows

The rheology of surface granular flows is investigated by means of measurements of velocity and number density profiles in a quasi-two-dimensional rotating cylinder, half-filled with mono-disperse steel balls. The measurements are made at the center of the cylinder, where the flow is fully-developed, using streakline photography and image analysis . The stress profile is computed from the number density profile using a force balance taking into account wall friction. The profiles for the mean velocity superimpose when distance is scaled by the particle diameter and the velocity by a characteristic shear rate and the particle diameter. The mean velocity is found to decay exponentially with depth in the bed with a decay length of $λ=1.1d$. The r.m.s. velocity is nearly constant near the free surface and below a transition point it decays linearly with depth. The shear rate, obtained by numerical differentiation of the velocity profile, shows a maximum which occurs at the same depth as the transition in the r.m.s. velocity profile. The velocity distribution is Maxwellian above the transition point and a Poisson velocity distribution is obtained deep in the layer. The variation of the apparent viscosity ($η$) with r.m.s. velocity ($u$) shows a relatively sharp transition at the shear rate maximum, and in the region below this point the apparent viscosity varies as $η\sim u^{-1.5}$. The experimental data is compared to predictions of three models for granular flow.