Source author record

A. V. Shutov

A. V. Shutov appears in the imported research catalog. Authorship, coauthor and topic links are available while profile ownership is still unclaimed.

ResearcherUnclaimed source record

math.NA cond-mat.mtrl-sci hep-ex math-ph math.CA math.MP nucl-ex physics.ins-det physics.optics physics.plasm-ph

Catalog footprint

What is connected

10works

10topics

4close collaborators

Actions

Connect this record

Open graph Browse works

Inspect adjacent papers, topics, institutions and collaborators without losing the researcher page.

Building this map preview

BZPEER is loading the nearby papers, people, topics and institutions for this page.

preprint2019arXiv

Measurement of neutron and proton analyzing powers on $C$, $CH$, $CH_2$ and $Cu$ targets in the momentum region 3-4.2 GeV/c

The analyzing powers for proton elastic scattering ($\vec p A\to pX$) and neutron charge exchange ($\vec n A\to p X$) reactions on nuclei have been measured on $ C$, $CH$, $CH_2$ and $Cu$ targets at incident neutron momenta 3.0 - 4.2 GeV/c by detecting one charged particle in forward direction. The polarized neutron measurements are the first of their kind. The experiment was performed using the Nuclotron accelerator in JINR Dubna, where polarized neutrons and protons were obtained from breakup of a polarized deuteron beam which has a maximum momentum of 13 GeV/c. The polarimeter ALPOM2 was used to obtain the analyzing power dependence on the transverse momentum of the final-state nucleon. These data have been used to estimate the figure of merit of a proposed experiment at Jefferson Laboratory to measure the recoiling neutron polarization in the quasi-elastic $^2H(\vec e,e'\vec n)$ reaction, which yields information on the charge and magnetic elastic form factors of the neutron.

preprint2016arXiv

Development of the MRPC for the TOF system of the MultiPurpose Detector

The Multipurpose Detector (MPD) \cite{cite1.MPD_CDR} is designed to study of hot and dense baryonic matter in collisions of heavy ions over the atomic mass range 1--197 at the centre of mass energy up to $\sqrt{S_{NN}}$ = 11 GeV (for Au79+). The MPD experiment will be carried out at the JINR accelerator complex NICA \cite{cite2.NICA_CDR} which is under construction. The barrel part of the MPD consists of various detectors surrounding the interaction point. It includes a precise tracking system (time projection chamber (TPC) and silicon inner tracker (IT)) and high-performance particle identification system based on time-of-flight (TOF) and calorimeter (ECal). The triple-stack multigap resistive plate chamber is chosen as an active element of the TOF. It provides good time resolution and long term stability. This article presents parameters of the MRPC obtained using the deuteron beam of JINR accelerator Nuclotron. The time resolution is $\sim$40 ps with efficiency of 99\%. Rate capability studies resulted with a time resolution of 60 ps and efficiency higher than 90\% on the beam with particle flux densities up to 2 kHz/cm$^2$.

preprint2016arXiv

Efficient implicit integration for finite-strain viscoplasticity with a nested multiplicative split

An efficient and reliable stress computation algorithm is presented, which is based on implicit integration of the local evolution equations of multiplicative finite-strain plasticity/viscoplasticity. The algorithm is illustrated by an example involving a combined nonlinear isotropic/kinematic hardening; numerous backstress tensors are employed for a better description of the material behavior. The considered material model exhibits the so-called weak invariance under arbitrary isochoric changes of the reference configuration, and the presented algorithm retains this useful property. Even more: the weak invariance serves as a guide in constructing this algorithm. The constraint of inelastic incompressibility is exactly preserved as well. The proposed method is first-order accurate. Concerning the accuracy of the stress computation, the new algorithm is comparable to the Euler Backward method with a subsequent correction of incompressibility (EBMSC) and the classical exponential method (EM). Regarding the computational efficiency, the new algorithm is superior to the EBMSC and EM. Some accuracy tests are presented using parameters of the aluminum alloy 5754-O and the 42CrMo4 steel. FEM solutions of two boundary value problems using MSC.MARC are presented to show the correctness of the numerical implementation.

preprint2015arXiv

Ductile damage model for metal forming simulations including refined description of void nucleation

We address the prediction of ductile damage and material anisotropy accumulated during plastic deformation of metals. A new model of phenomenological metal plasticity is proposed which is suitable for applications involving large deformations of workpiece material. The model takes combined nonlinear isotropic/kinematic hardening, strain-driven damage and rate-dependence of the stress response into account. Within this model, the work hardening and the damage evolution are fully coupled. The description of the kinematics is based on the double multiplicative decomposition of the deformation gradient proposed by Lion. An additional multiplicative decomposition is introduced in order to account for the damage-induced volume increase of the material. The model is formulated in a thermodynamically admissible manner. Within a simple example of the proposed framework, the material porosity is adopted as a rough measure of damage. A new simple void nucleation rule is formulated based on the consideration of various nucleation mechanisms. In particular, this rule is suitable for materials which exhibit a higher void nucleation rate under torsion than in case of tension. The material model is implemented into the FEM code Abaqus and a simulation of a deep drawing process is presented. The robustness of the algorithm and the performance of the formulation is demonstrated.

preprint2014arXiv

Analysis of some basic approaches to finite strain elasto-plasticity in view of reference change

There is a large variety of concepts used to generalize the classical Prandtl-Reuss relations of infinitesimal elasto-plasticity to finite strains. In this work, some basic approaches are compared in a qualitative way with respect to a certain invariance property. These basic approaches include the additive hypoelasto-plasticity with corotational stress rates, additive plasticity in the logarithmic strain space, and multiplicative hyperelasto-plasticity. The notion of weak invariance is introduced in this study. Roughly speaking, a material model is weakly invariant under a certain transformation of the local reference configuration if this reference change can be neutralized by a suitable transformation of initial conditions, leaving the remaining constitutive relations intact. We analyse the basic models in order to find out if they are weakly invariant under arbitrary volume-preserving transformations of the reference configuration. It is shown that the weak invariance property corresponds to a generalized symmetry which provides insights into underlying constitutive assumptions. This property can be used for a systematic study of different frameworks of finite strain elasto-plasticity. In particular, it can be used as a classification criterion.

preprint2013arXiv

On a dislocation density based two-phase plasticity model: refinement and extension to non-proportional loading

The two-phase composite approach of Estrin et al. (1998) describes an evolving dislocation cell structure. Mckenzie et al. (2007) enhanced the model to capture the effects of hydrostatic pressure and temperature during severe plastic deformation. The goal of the present study is to incorporate this microstructural model into the macroscopic viscoplasticity framework proposed by Shutov and Kreißig (2008a). Thereby, the two-phase composite approach is examined carefully. Both physical and numerical drawbacks are revealed and possible solutions are presented, thus leading to a refined micro model. Moreover, some improvements concerning reliable parameter identification are suggested as well. The material parameters of the refined micro model are identified for an aluminum alloy using TEM cell size measurements. Then, an extension to non-proportional deformation is performed in such a way that the evolution of dislocation densities becomes sensitive to load path changes. Experimental findings suggest that such deformation modes can significantly influence the evolution of microstructure, including the dissolution of cells and the reduction of total dislocation density shortly after the load path change. In order to capture such effects, some tensor-valued state variables are introduced which couple the refined micro model with the macroscopic viscoplasticity model. As a result, a new system of constitutive equations is obtained. In order to demonstrate its capability to respond to load path changes, load cases as typical for Equal Channel Angular Pressing (ECAP) are considered. The obtained evolution of dislocation populations differs signficantly depending on which ECAP route is applied.

preprint2012arXiv

A viscoplasticity model with an enhanced control of the yield surface distortion

A new model of metal viscoplasticity, which takes combined isotropic, kinematic, and distortional hardening into account, is presented. The basic modeling assumptions are illustrated using a new two-dimensional rheological analogy. This demonstrative rheological model is used as a guideline for the construction of constitutive relations. The nonlinear kinematic hardening is captured using the well-known Armstrong-Frederick approach. The distortion of the yield surface is described with the help of a so-called distortional backstress. A distinctive feature of the model is that any smooth convex saturated form of the yield surface which is symmetric with respect to the loading direction can be captured. In particular, an arbitrary sharpening of the saturated yield locus in the loading direction combined with a flattening on the opposite side can be covered. Moreover, the yield locus evolves smoothly and its convexity is guaranteed at each hardening stage. A strict proof of the thermodynamic consistency is provided. Finally, the predictive capabilities of the material model are verified using the experimental data for a very high work hardening annealed aluminum alloy 1100 Al.

preprint2012arXiv

Triggering and guiding electric discharge by a train of UV picosecond pulses combined with a long UV pulse

Non-self-sustained electric discharge and electric breakdown were triggered and guided by a train of picosecond UV pulses overlapped with a long free-running UV pulse of a hybrid Ti:Sapphire-KrF laser facility. Photocurrent sustained by this train is two orders of magnitude higher, and electric breakdown distance is twice longer than those for the discharge triggered by the long UV pulse only.

preprint2009arXiv

Geometric integrators for multiplicative viscoplasticity: analysis of error accumulation

The inelastic incompressibility is a typical feature of metal plasticity/viscoplasticity. Over the last decade, there has been a great amount of research related to construction of numerical integration algorithms which exactly preserve this geometric property. In this paper we examine, both numerically and mathematically, the excellent accuracy and convergence characteristics of such geometric integrators. In terms of a classical model of finite viscoplasticity, we illustrate the notion of exponential stability of the exact solution. We show that this property enables the construction of effective and stable numerical algorithms, if incompressibility is exactly satisfied. On the other hand, if the incompressibility constraint is violated, spurious degrees of freedom are introduced. This results in the loss of the exponential stability and a dramatic deterioration of convergence behavior.

preprint2007arXiv

Finite strain viscoplasticity with nonlinear kinematic hardening: phenomenological modeling and time integration

This article deals with a viscoplastic material model of overstress type. The model is based on a multiplicative decomposition of the deformation gradient into elastic and inelastic part. An additional multiplicative decomposition of inelastic part is used to describe a nonlinear kinematic hardening of Armstrong-Frederick type. Two implicit time-stepping methods are adopted for numerical integration of evolution equations, such that the plastic incompressibility constraint is exactly satisfied. The first method is based on the tensor exponential. The second method is a modified Euler-Backward method. Special numerical tests show that both approaches yield similar results even for finite inelastic increments. The basic features of the material response, predicted by the material model, are illustrated with a series of numerical simulations.