Source author record

Yury Gogotsi

Yury Gogotsi appears in the imported research catalog. Authorship, coauthor and topic links are available while profile ownership is still unclaimed.

ResearcherUnclaimed source record

cond-mat.mtrl-sci cond-mat.soft cond-mat.mes-hall physics.app-ph

Catalog footprint

What is connected

5works

4topics

4close collaborators

Actions

Connect this record

Open graph Browse works

Inspect adjacent papers, topics, institutions and collaborators without losing the researcher page.

Building this map preview

BZPEER is loading the nearby papers, people, topics and institutions for this page.

preprint2022arXiv

Removal and Recovery of Ammonia from Wastewater using Ti$_3$C$_2$T$_x$ MXenes in Flow Electrode Capacitive Deionization

Flowing electrode capacitive deionization systems (FE-CDI) have recently garnered attention because of their ability to prevent cross contamination and operate in uninterrupted cycles ad infinitum. Typically, FE-CDI electrodes suffer from low conductivity, reducing deionization performance. Utilization of higher mass loadings to combat this leads to poor rheological properties. Herein, Ti$_3$C$_2$T$_x$ MXene was introduced as 1 mg/mL slurry electrodes in an FE-CDI system for the removal and recovery of ammonia from simulated agricultural wastewater. The electrode performance was evaluated by operating the FE-CDI system with a feed solution of 500 mg/L NH$_4$Cl running in batch mode at a constant voltage of 1.20 V and -1.20 V in charging and discharging modes, respectively. Despite the low loading, Ti$_3$C$_2$T$_x$ flowing electrodes showed markedly improved performance, achieving 60% ion removal efficiency in a saturation time of 115 minutes with an adsorption capacity of 460 mg/g. To understand the high adsorption performance of the electrodes, physiochemical and structural analysis was done via a variety of characterization techniques such as SEM, TEM, XRD, DLS, and Raman Spectroscopy. Cyclic Voltammetry and Galvanostatic charge/discharge profiles were obtained to evaluate the electrochemical properties of the electrodes. The system proved to be an energy-saving technology by exhibiting a charge efficiency of 58-70% while operating at an energy consumption of 0.45 kWh/kg. A 92% regeneration efficiency showed that the electrodes were stable and suitable for long term and scalable usage. The results demonstrate that MXenes have the potential to improve the FE-CDI process for energy-efficient removal and recovery of ammonia.

preprint2021arXiv

Multi-modal Spectroscopic Study of Surface Termination Evolution in Cr2TiC2Tx MXene

Control of surface functionalization of MXenes holds great potential, and in particular, may lead to tuning of magnetic and electronic order in the recently reported magnetic Cr2TiC2Tx. Here, vacuum annealing experiments of Cr2TiC2Tx are reported with in situ electron energy loss spectroscopy and novel in situ Cr K-edge extended energy loss fine structure analysis, which directly tracks the evolution of the MXene surface coordination environment. These in situ probes are accompanied by benchmarking synchrotron X-ray absorption fine structure measurements and density functional theory calculations. With the etching method used here, the MXene has an initial termination chemistry of Cr2TiC2O1.3F0.8. Annealing to 600 C results in the complete loss of -F, but -O termination is thermally stable up to (at least) 700 C. These findings demonstrate thermal control of -F termination in Cr2TiC2Tx and offer a first step towards termination engineering this MXene for magnetic applications. Moreover, this work demonstrates high energy electron spectroscopy as a powerful approach for surface characterization in 2D materials.

preprint2014arXiv

Interfacial Ionic Liquids: Connecting Static and Dynamic Structures

It is well-known that room temperature ionic liquids (RTILs) often adopt a charge-separated layered structure, i.e., with alternating cation- and anion-rich layers, at electrified interfaces. However, the dynamic response of the layered structure to temporal variations in applied potential is not well understood. We used in situ, real-time X-ray reflectivity (XR) to study the potential-dependent electric double layer (EDL) structure of an imidazolium-based RTIL on charged epitaxial graphene during potential cycling as a function of temperature. The results suggest that the graphene-RTIL interfacial structure is bistable in which the EDL structure at any intermediate potential can be described by the combination of two extreme-potential structures whose proportions vary depending on the polarity and magnitude of the applied potential. This picture is supported by the EDL structures obtained by fully atomistic molecular dynamics (MD) simulations at various static potentials. The potential-driven transition between the two structures is characterized by an increasing width but with an approximately fixed hysteresis magnitude as a function of temperature. The results are consistent with the coexistence of distinct anion and cation adsorbed structures separated by an energy barrier (~0.15 eV).

preprint2014arXiv

MXenes as High Capacity Electrode Materials for Metal (Li, Na, K, Ca)-ion batteries

Two-dimensional (2D) materials can have an excellent capability to handle high rates of charge in ion batteries since metal ions need not diffuse in a 3D lattice structure. However graphene, which is the most important 2D material, is known to have no Li capacity. Herein, adsorption of Li, as well as Na, K, and Ca on Ti$_3$C$_2$, one representative MXene, is predicted by first-principles density functional calculations. In our study, we observed that these alkali ions exhibit different adsorption energy depending on the coverage. The adsorption energies of Na, K and Ca decrease as coverage increases, while Li shows little sensitivity to variance in coverage. This observed relationship between adsorption energies and coverage of alkali ions on Ti$_3$C$_2$ can be explained by their effective ionic radii. A larger effective ionic radius increases interaction between alkali atoms, thus lower capacity and coverage are obtained. Our calculated capacity values for Li, Na, K and Ca on Ti$_3$C$_2$ are 639.5, 319.8, 191.8 and 159.9 mAh g$^{-1}$, respectively. Compared to materials currently used in Li ion battery anodes, MXene shows great promise in increasing overall battery performance.

preprint2012arXiv

Understanding Controls on Interfacial Wetting at Epitaxial Graphene: Experiment and Theory

The interaction of interfacial water with graphitic carbon at the atomic scale is studied as a function of the hydrophobicity of epitaxial graphene. High resolution X-ray reflectivity shows that the graphene-water contact angle is controlled by the average graphene thickness, due to the fraction of the film surface expressed as the epitaxial buffer layer whose contact angle (contact angle θ_c = 73°) is substantially smaller than that of multilayer graphene (θ_c = 93°). Classical and ab initio molecular dynamics simulations show that the reduced contact angle of the buffer layer is due to both its epitaxy with the SiC substrate and the presence of interfacial defects. This insight clarifies the relationship between interfacial water structure and hydrophobicity, in general, and suggests new routes to control interface properties of epitaxial graphene.