Source author record

Wanming Liu

Wanming Liu appears in the imported research catalog. Authorship, coauthor and topic links are available while profile ownership is still unclaimed.

ResearcherUnclaimed source record

Catalog footprint

What is connected

8works
4topics
4close collaborators

Actions

Connect this record

Log in to claim

Research graph

See the researcher in context

Open full explorer

Inspect adjacent papers, topics, institutions and collaborators without losing the researcher page.

Building this map preview

BZPEER is loading the nearby papers, people, topics and institutions for this page.

Published work

8 published item(s)

preprint2021arXiv

Ampere-class Bright Field Emission Cathode Operated at 100 MV/m

High current bright sources are needed to power the next generation of compact rf and microwave systems. A major requirement is that such a source could be sustainably operated at high frequencies, well above 1 GHz, and high gradients, well above 100 MV/m. Field emission sources offer simplicity and scalability in a high frequency era of the injector design, but the output rf cycle charge and high gradient operation remain a great and largely unaddressed challenge. Here, a field emission cathode based on ultra-nano-crystalline diamond or UNCD, an efficient planar field emission material, was tested at 100 MV/m in an L-band injector. A very high charge of 38 pC per rf cycle (300 nC per rf pulse corresponding to rf pulse current of 120 mA) was demonstrated. This operating condition revealed a space charge dominated emission from the cathode and revealed a condition under which the 1D Child Langmuir limit was surpassed. Finally, a beam brightness of $\sim 10^{14}-10^{15}$ A/m$^2\times$rad$^2$ was estimated.

preprint2020arXiv

Rapid thermal emittance and quantum efficiency mapping of a cesium telluride cathode in an rf photoinjector using multiple laser beamlets

Thermal emittance and quantum efficiency (QE) are key figures of merit of photocathodes, and their uniformity is critical to high-performance photoinjectors. Several QE mapping technologies have been successfully developed; however, there is still a dearth of information on thermal emittance maps. This is because of the extremely time-consuming procedure to gather measurements by scanning a small beam across the cathode with fine steps. To simplify the mapping procedure, and to reduce the time required to take measurements, we propose a new method that requires only a single scan of the solenoid current to simultaneously obtain thermal emittance and QE distribution by using a pattern beam with multiple beamlets. In this paper, its feasibility has been confirmed by both beam dynamics simulation and theoretical analysis. The method has been successfully demonstrated in a proof-of-principle experiment using an L-band radiofrequency photoinjector with a cesium telluride cathode. In the experiment, seven beamlets were generated from a microlens array system and their corresponding thermal emittance and QE varied from 0.93 to 1.14 $μ$m/mm and from 4.6 to 8.7%, respectively. We also discuss the limitations and future improvements of the method in this paper.

preprint2019arXiv

Development and high-power testing of an X-band dielectric-loaded power extractor

Dielectric loaded structures are promising candidates for use in the structure wakefield acceleration (SWFA) technique, for both the collinear wakefield and the two-beam acceleration (CWA and TBA respectively) approaches, due to their low fabrication cost, low rf losses, and the potential to withstand high gradient. A short pulse (<=20 ns) TBA program is under development at the Argonne Wakefield Accelerator (AWA) facility where dielectric loaded structures are being used for both the power extractor/transfer structure (PETS) and the accelerator. In this study, an X-band 11.7 GHz dielectric PETS was developed and tested at the AWA facility to demonstrate high power wakefield generation. The PETS was driven by a train of eight electron bunches separated by 769.2 ps (9 times of the X-band rf period) in order to achieve coherent wakefield superposition. A total train charge of 360 nC was passed through the PETS structure to generate ~200 MW, ~3 ns flat-top rf pulses without rf breakdown. A future experiment is being planned to increase the generated rf power to approximately ~1 GW by optimizing the structure design and improving the drive beam quality.

preprint2014arXiv

Planar Ultrananocrystalline Diamond Field Emitter in Accelerator RF Electron Injector: Performance Metrics

A case performance study of a planar field emission cathode (FEC) based on nitrogen-incorporated ultrananocrystalline diamond, (N)UNCD, was carried out in an RF 1.3 GHz electron gun. The FEC was a 100 nm (N)UNCD film grown on a 20 mm diameter stainless steel disk with a Mo buffer layer. At surface gradients 45-65 MV/m, peak currents of 1-80 mA (equivalent to 0.3-25 mA/cm$^2$) were achieved. Imaging with two YAG screens confirmed emission from the (N)UNCD surface with (1) the beam emittance of 1.5 mm$\times$mrad/mm-rms, and (2) longitudinal FWHM and rms energy spread of 0.7% and 11% at an electron energy of 2 MeV. Current stability was tested over the course of 36$\times$10$^3$ RF pulses (equivalent to 288$\times$10$^6$ GHz oscillations).

preprint2013arXiv

Positron Source Simulations for ILC 1 TeV Upgrade

The generation and capture of polarized positrons at a source with a superconducting helical undulator having 4.3 cm period and 500 GeV electron drive beam have been simulated. The positron polarization has been calculated for the different undulator K values (up to K = 2.5). Without applying a photon collimator, the maximal polarization of positrons is about 25% for 231 meters active magnet length of undulator with K = 0.7. Using an undulator with K = 2.5 and a collimator with an aperture radius of 0.9 mm results in increase of positron polarization to 54%. The energy deposition, temperature rise and stress induced by high intense photon beam in the rotated titanium-alloy target have been estimated. The maximal thermal stress in the target is about 224 MPa for the source with photon collimation to achieve a positron polarization of 54%.

preprint2013arXiv

The International Linear Collider Technical Design Report - Volume 3.I: Accelerator R&D in the Technical Design Phase

The International Linear Collider Technical Design Report (TDR) describes in four volumes the physics case and the design of a 500 GeV centre-of-mass energy linear electron-positron collider based on superconducting radio-frequency technology using Niobium cavities as the accelerating structures. The accelerator can be extended to 1 TeV and also run as a Higgs factory at around 250 GeV and on the Z0 pole. A comprehensive value estimate of the accelerator is give, together with associated uncertainties. It is shown that no significant technical issues remain to be solved. Once a site is selected and the necessary site-dependent engineering is carried out, construction can begin immediately. The TDR also gives baseline documentation for two high-performance detectors that can share the ILC luminosity by being moved into and out of the beam line in a "push-pull" configuration. These detectors, ILD and SiD, are described in detail. They form the basis for a world-class experimental programme that promises to increase significantly our understanding of the fundamental processes that govern the evolution of the Universe.

preprint2013arXiv

The International Linear Collider Technical Design Report - Volume 3.II: Accelerator Baseline Design

The International Linear Collider Technical Design Report (TDR) describes in four volumes the physics case and the design of a 500 GeV centre-of-mass energy linear electron-positron collider based on superconducting radio-frequency technology using Niobium cavities as the accelerating structures. The accelerator can be extended to 1 TeV and also run as a Higgs factory at around 250 GeV and on the Z0 pole. A comprehensive value estimate of the accelerator is give, together with associated uncertainties. It is shown that no significant technical issues remain to be solved. Once a site is selected and the necessary site-dependent engineering is carried out, construction can begin immediately. The TDR also gives baseline documentation for two high-performance detectors that can share the ILC luminosity by being moved into and out of the beam line in a "push-pull" configuration. These detectors, ILD and SiD, are described in detail. They form the basis for a world-class experimental programme that promises to increase significantly our understanding of the fundamental processes that govern the evolution of the Universe.

preprint2011arXiv

A conventional positron source for International Linear Collider

A possible solution to realize a conventional positron source driven by a several-GeV electron beam for the International Linear Collider is proposed. A 300 Hz electron linac is employed to create positrons with stretching pulse length in order to cure target thermal load. ILC requires about 2600 bunches in a train which pulse length is 1 ms. Each pulse of the 300 Hz linac creates about 130 bunches, then 2600 bunches are created in 63 ms. Optimized parameters such as drive beam energy, beam size, and target thickness, are discussed assuming a L-band capture system to maximize the capture efficiency and to mitigate the target thermal load. A slow rotating tungsten disk is employed as positron generation target.