Source author record

Timing Qu

Timing Qu appears in the imported research catalog. Authorship, coauthor and topic links are available while profile ownership is still unclaimed.

ResearcherUnclaimed source record

cond-mat.mtrl-sci cond-mat.supr-con physics.app-ph

Catalog footprint

What is connected

3works

3topics

4close collaborators

Actions

Connect this record

Open graph Browse works

Inspect adjacent papers, topics, institutions and collaborators without losing the researcher page.

Building this map preview

BZPEER is loading the nearby papers, people, topics and institutions for this page.

preprint2019arXiv

Screening current effect on the stress and strain distribution in REBCO high-field magnets: experimental verification and numerical analysis

Besides screening-current-induced magnetic fields (SCIF), the shielding effect in high-Tc coated conductors also has an strong influence on its strain distribution in a coil winding, especially during high-field operations. To demonstrate this phenomenon, a special experimental setup was designed. With an LTS background magnet and a small HTS insert coil, we were able to carry out direct observations on the hoop strains of a 10-mm wide REBCO sample. Measured data was compared against numerical solutions solved by electromagnetic models based on T -A formulation and homogeneous mechanical models, showing good agreements. An analytical expression was proposed to estimate the maximum radial Lorentz force considering shielding effect. Using the developed numerical models, we further studied the potential effects of two of the mostly investigated methods, which were formerly introduced to reduce SCIF, including multi-filamentary conductors and current sweep reversal (CSR) approach.

preprint2016arXiv

Critical Current Survival in YBCO Superconducting Layer of the Delaminated Coated Conductor

High temperature superconducting coated conductor (CC) could be practically applied in electric equipment due to its favorable mechanical properties and the critical current performance of YBCO superconducting layer. It is well known that CC could be easily delaminated because of its poor stress tolerance in thickness direction, i.e. along the c-axis of YBCO. Commonly, a stack including YBCO layer and silver stabilizer could be obtained after the delamination. It would be interesting to investigate the superconducting properties of the delaminated stack, since it could also be considered as a new type of CC with the silver stabilizer as the buffer layer, which is quite different from the oxide buffer layers in the traditional CC and might lead to new applications. In this study, a CC sample was delaminated by liquid nitrogen immersing. A Hall probe scanning system was employed to measure the critical current (IC) distribution of the original sample and the obtained stack. It was found that IC could be partially preserved after the delamination. Dense and crack-free morphologies of the delaminated surfaces were observed by scanning electron microscopy, and the potential application of the obtained stack in superconducting joint technology was discussed.

preprint2013arXiv

A Low-Fluorine Solution with the F/Ba Mole Ratio of 2 for the Fabrication of YBCO Films

In the reported low-fluorine MOD-YBCO studies, the lowest F/Ba mole ratio of the precursor solution was 4.5. However, further lowering the F/Ba ratio is important according to the researches of YBCO thick film. On the other hand, the F/Ba ratio is necessary to be at least 2 for the full conversion of the Ba precursor to BaF_2 to avoid the formation of BaCO_3, which is detrimental to the superconducting performance. In this study, a novel solution with the F/Ba mole ratio of 2 was developed, in which the fluorine content was only about 10.3% of that used in the conventional TFA-MOD method. Attenuated total reflectance-Fourier transformed-infrared spectra(ATR-FT-IR) revealed that BaCO_3 was remarkably suppressed in the as-pyrolyzed film and eliminated at 700 Celsius degree. Thus YBCO films with a critical current density (J_c) over 5 MA cm^{-2} (77 K, 0 T, 200 nm thickness) could be obtained on LAO single crystal substrates. In-situ FT-IR spectra showed that no obvious fluorinated gaseous by-products were detected in the pyrolysis step, which indicated that all of the F atoms might remain in the film as fluorides. X-ray diffraction (XRD) θ/2θ-scan showed that BaF_2, but neither YF_3 nor CuF_2, was detected in the films quenched at 400 - 800 Celsius degree. The formation priority of BaF_2 over YF_3 and CuF_2 was interpreted by the chemical equilibrium of the potential reactions. Our study could enlarge the synthesis window of the precursor solution for MOD-YBCO fabrication and open a gate to study the fluorine content in the precursor solution continuously and systematically.