Source author record

P. Hosemann

P. Hosemann appears in the imported research catalog. Authorship, coauthor and topic links are available while profile ownership is still unclaimed.

ResearcherUnclaimed source record

cond-mat.mtrl-sci physics.acc-ph nucl-ex physics.ins-det

Catalog footprint

What is connected

5works

4topics

4close collaborators

Actions

Connect this record

Open graph Browse works

Inspect adjacent papers, topics, institutions and collaborators without losing the researcher page.

Building this map preview

BZPEER is loading the nearby papers, people, topics and institutions for this page.

preprint2021arXiv

Compositionally Graded SS316 to C300 Maraging Steel using Additive Manufacturing

Joining of dissimilar metals is required for numerous applications in industries such as chemical, energy and automotive. It is challenging due to differences in melting point, density, and thermal expansion of the metals being joined. Common welding techniques involve limiting melting and solidification to a narrow area leading to high thermal stresses and potentially brittle intermetallic phases. Furthermore, the geometric complexity of these welded joints can be rather limited. Additive Manufacturing (AM) presents new techniques for joining of dissimilar metals. One of the emerging methods is the building of functionally graded parts using Directed Energy Deposition (DED) to spatially vary composition. In this paper, a SS316L and C300 maraging steel couple were joined by DED and heat treated. 13 discrete composition layers were selected using metallurgical considerations, in order to ensure a smooth transition in properties and microstructure. The mechanical properties of the as-built joints were found to be similar to the SS part and no intermetallic phases were found in the interface.

preprint2021arXiv

Quantifying residual stress in Helium implanted surfaces and its implication for blistering

Helium implantation in surfaces is of interest for plasma facing materials and other nuclear applications. Vanadium as both a representative bcc material and a material relevant for fusion applications is implanted using a Helium ion beam microscope, and the resulting swelling and nanomechanical properties are quantified. These values are put in correlation to data obtained from micro residual stress measurements using a focused ion beam based ring-core technique. We found that the swelling measured is similar to literature values. Further we are able to measure the surface stress caused by the implantation and find it approaches the yield strength of the material at blistering doses. The simple calculations performed in the present work, along with several geometrical considerations deduced from experimental results confirm the driving force for blister formation comes from bulging resulting mainly from gas pressure buildup, rather than solely stress induced buckling.

preprint2020arXiv

Atom probe characterisation of segregation driven Cu and Mn-Ni-Si co-precipitation in neutron irradiated T91 tempered-martensitic steel

The T91 grade and similar 9Cr tempered-martensitic steels (also known as ferritic-martensitic) are leading candidate structural alloys for fast fission nuclear and fusion power reactors. At low temperatures (300 to 400 $^\circ$C) neutron irradiation hardens and embrittles these steels, therefore it is important to investigate the origin of this mode of life limiting property degradation. T91 steel specimens were separately neutron irradiated to 2.14 dpa at 327 $^\circ$C and 8.82 dpa at 377 $^\circ$C in the Idaho National Laboratory Advanced Test Reactor. Atom probe tomography was used to investigate the segregation driven formation of Mn-Ni-Si-rich (MNSPs) and Cu-rich (CRP) co-precipitates. The precipitates increase in size and, slightly, in volume fraction at the higher irradiation temperature and dose, while their corresponding compositions were very similar, falling near the Si(Mn,Ni) phase field in the Mn-Ni-Si projection of the Fe-based quaternary phase diagram. While the structure of the precipitates has not been characterized, this composition range is distinctly different than that of the typically cited G-phase. The precipitates are composed of CRP with MNSP appendages. Such features are often observed in neutron irradiated reactor pressure vessel (RPV) steels. However, the Si, Ni, Mn, P and Cu solutes concentrations are lower in the T91 than in typical RPV steels. Thus, in T91 precipitation primarily takes place in solute segregated regions of line and loop dislocations. These results are consistent with the model for radiation induced segregation driven precipitation of MNSPs proposed by Ke et al. Cr-rich alpha prime ($α$') phase formation was not observed.

preprint2014arXiv

Accessing defect dynamics using intense, nanosecond pulsed ion beams

Gaining in-situ access to relaxation dynamics of radiation induced defects will lead to a better understanding of materials and is important for the verification of theoretical models and simulations. We show preliminary results from experiments at the new Neutralized Drift Compression Experiment (NDCX-II) at Lawrence Berkeley National Laboratory that will enable in-situ access to defect dynamics through pump-probe experiments. Here, the unique capabilities of the NDCX-II accelerator to generate intense, nanosecond pulsed ion beams are utilized. Preliminary data of channeling experiments using lithium and potassium ions and silicon membranes are shown. We compare these data to simulation results using Crystal Trim. Furthermore, we discuss the improvements to the accelerator to higher performance levels and the new diagnostics tools that are being incorporated.

preprint2013arXiv

Towards pump-probe experiments of defect dynamics with short ion beam pulses

A novel, induction type linear accelerator, the Neutralized Drift Compression eXperiment (NDCX-II), is currently being commissioned at Berkeley Lab. This accelerator is designed to deliver intense (up to 3x1011 ions/pulse), 0.6 to ~600 ns duration pulses of 0.13 to 1.2 MeV lithium ions at a rate of about 2 pulses per minute onto 1 to 10 mm scale target areas. When focused to mm-diameter spots, the beam is predicted to volumetrically heat micrometer thick foils to temperatures of ~30,000 K. At lower beam power densities, the short excitation pulse with tunable intensity and time profile enables pump-probe type studies of defect dynamics in a broad range of materials. We briefly describe the accelerator concept and design, present results from beam pulse shaping experiments and discuss examples of pump-probe type studies of defect dynamics following irradiation of materials with intense, short ion beam pulses from NDCX-II.