Source author record

Munemasa Machida

Munemasa Machida appears in the imported research catalog. Authorship, coauthor and topic links are available while profile ownership is still unclaimed.

ResearcherUnclaimed source record

physics.plasm-ph physics.ins-det

Catalog footprint

What is connected

4works

2topics

4close collaborators

Actions

Connect this record

Open graph Browse works

Inspect adjacent papers, topics, institutions and collaborators without losing the researcher page.

Building this map preview

BZPEER is loading the nearby papers, people, topics and institutions for this page.

preprint2020arXiv

Four-electrodes DBD plasma jet device with additional floating electrode

A Dielectric Barrier Discharge (DBD) plasma jet in a four electrodes configuration was investigated in order to improve the discharge parameters, such as, plasma power and rotational and vibrational temperatures of molecular species in the plasma plume. The improvement attempts were made by introducing an auxiliary floating electrode in a form of a metallic pin inside the DBD device. That piece was placed near the bottom of the main device, centered in relation to the four powered electrodes, which were covered with a dielectric material. By using metallic pins with different lengths, it was observed that there were considerable variations of the plasma parameters as a function of the pin length. Two carrier gases were tested: argon and helium. With helium as the working gas, it was found that there is an optimal pin length that maximizes the plasma power and its vibrational temperature. In addition, it was verified that for the pin of optimum length the relative intensity of light emissions from OH and NO species achieved higher values than in other conditions studied.

preprint2018arXiv

The role of vibrational temperature variations in a pulsed dielectric barrier discharge plasma device

The use of dielectric barrier discharge (DBD) plasmas has become a practical way to carry out surface treatment and one seeks to do it in a more efficient way, which requires to have control of the plasma parameters like rotational and vibrational temperatures (T_rot and T_vib). Since the T_vib of an atmospheric pressure plasma jet is an important parameter related to improvement of surface treatments, in this work it was analyzed two methods to increase the values of T_vib in the DBD plasma. One of the methods is to reduce the exit size of the DBD reactor, and the other is to change the gas flow rate. Explanations for the reasons that lead to the increment of the vibrational temperature are proposed in both cases.

preprint2015arXiv

Treatment of PDMS surfaces using pulsed DBD plasmas: comparing the use of different gases and its influence on adhesion

In this work we present some results of the treatment of polydimethylsiloxane (PDMS) surfaces using pulsed dielectric barrier discharge plasmas. The results of plasma treatment using different gases and mixtures, argon, argon plus water vapor, helium, helium plus water vapor, nitrogen and nitrogen plus water vapor, were compared testing the adhesion between two PDMS samples for each kind of plasma. We also studied the water contact angle in function of plasma process time of PDMS surfaces with each kind of plasma treatment. The plasma was characterized by optical emission spectroscopy (OES) to identify the emitting species and determine the plasma temperatures. The plasma temperature for each process was estimated comparing the spectrum obtained by OES with the spectrum generated by SpecAir simulation code. Measurements of power delivered to the plasmas were also performed. As the results, all the process using different gases show good adhesion efficacy between PDMS samples when long exposure time (larger than 150 seconds) is applied. However, when only a few discharges are applied to PDMS samples the helium plasma process presented best results. Atomic Force Microscopy (AFM) analysis of PDMS samples treated with helium plasma showed reduction in the surface roughness, which increase the surface contact area and improves the adhesion.

preprint2014arXiv

Generation of Cold Argon Plasma Jet at the End of Flexible Plastic Tube

This brief communication reports a new method for generation of cold atmospheric pressure plasma jet at the downstream end of a flexible plastic tube. The device consists of a small chamber where dielectric barrier discharge (DBD) is ignited in Argon. The discharge is driven by a conventional low frequency AC power supply. The exit of DBD reactor is connected to a commercial flexible plastic tube (up to 4 meters long) with a thin floating Cu wire inside. Under certain conditions an Ar plasma jet can be extracted from the downstream tube end and there is no discharge inside the plastic tube. The jet obtained by this method is cold enough to be put in direct contact with human skin without electric shock and can be used for medical treatment and decontamination.