Source author record

M. A. Monclús

M. A. Monclús appears in the imported research catalog. Authorship, coauthor and topic links are available while profile ownership is still unclaimed.

ResearcherUnclaimed source record

cond-mat.mtrl-sci physics.app-ph

Catalog footprint

What is connected

3works

2topics

4close collaborators

Actions

Connect this record

Open graph Browse works

Inspect adjacent papers, topics, institutions and collaborators without losing the researcher page.

Building this map preview

BZPEER is loading the nearby papers, people, topics and institutions for this page.

preprint2020arXiv

High temperature mechanical properties and microstructure of hard TaSiN coatings

Room and high temperature mechanical properties of reactive magnetron sputtered TaSiN coatings were measured using nanoindentation (between 25C and 500C). Fracture toughness was also evaluated at a similar temperature range using the micropillar splitting method. The influence of the nitrogen concentration on the evolving phases and microstructure of the TaSiN coatings, before and after the high temperature testing, were examined by X-ray diffraction (XRD) and transmission electron microscopy (TEM) analysis. XRD spectra showed broad peaks with hexagonal $γ$-Ta2N as the main phase, with the cubic $δ$-TaN phase emerging for higher N contents. Phase composition remained unchanged before and after the 500C tests. However, after the high temperature tests, TEM analysis showed the presence of an oxide surface layer, with a thickness that decreased (from 42 to 15 nm) with N content, due to residual oxygen diffusion, which replaces nitrogen to form amorphous SiOx. Beneath the oxide-rich surface layer, coatings exhibited a stable nanocrystalline columnar microstructure. Hardness and fracture toughness increased with N content, initially due to the formation of an amorphous Si-N tissue at grain boundaries, and for even higher N contents, due to the appearance of the hard cubic $δ$-TaN phase. Hardness at 500C decreased only by 15%, while fracture toughness followed the opposite trend, due to increased plasticity with temperature. The optimum composition turned out to be Ta55Si10N35, which retained a hardness of 30 GPa at 500C, being also the toughest. These observations make this system very interesting for high temperature applications.

preprint2020arXiv

High temperature strength retention of Cu/Nb nanolaminates through dynamic strain ageing

The mechanical properties of Cu/Nb metallic nanolaminates with different layer thickness (7, 16, 34 and 63 nm) were studied by means of micropillar compression tests from room temperature to 400 C. Both strain-rate jump and constant strain rate tests were carried out and they showed evidence of dynamic strain ageing in the nanolaminates with 7, 16 and 34 nm layer thickness deformed at 200 C. Dynamic strain ageing was accompanied by a reduction of the strain rate sensitivity to 0, high strength retention at 200 C and the development of shear localization of the deformation at low strains (5%-6%) that took place along the Nb layers in the nanolaminates. Atom probe tomography of the deformed specimens revealed the presence of O in solid solution in the Nb layers but not in the Cu layers. Thus, diffusion of O atoms to the mobile dislocations in Nb was found to be the origin of the dynamic strain ageing in the Cu/Nb nanolaminates around 200 C. This mechanism was not found at higher temperatures (400 C) because deformation was mainly controlled by stress-assisted diffusion in the Cu layers. This discovery shows a novel strategy to enhance the strength retention at high temperature of metallic nanolaminates through dynamic strain ageing of one the phases.

preprint2016arXiv

Selective oxidation-induced strengthening of Zr/Nb nanoscale multilayers

The paper presents a new approach, based on controlled oxidation of nanoscale metallic multilayers, to produce strong and hard oxide/metal nanocomposite coatings with high strength and good thermal stability. The approach is demonstrated by performing long term annealing on sputtered Zr/Nb nanoscale metallic multilayers and investigating the evolution of their microstructure and mechanical properties by combining analytical transmission electron microscopy, nano-mechanical tests and finite element models. As-deposited multilayers were annealed at 350 C in air for times ranging between 1 - 336 hours. The elastic modulus increased by approx. 20% and the hardness by approx. 42% after 15 hours of annealing. Longer annealing times did not lead to changes in hardness, although the elastic modulus increased up to 35% after 336 hrs. The hcp Zr layers were rapidly transformed into monoclinic ZrO2 (in the first 15 hours), while the Nb layers were progressively oxidised, from top surface down towards the substrate, to form an amorphous oxide phase at a much lower rate. The sequential oxidation of Zr and Nb layers was key for the oxidation to take place without rupture of the multi-layered structure and without coating spallation, as the plastic deformation of the metallic Nb layers allowed for the partial relieve of the residual stresses developed as a result of the volumetric expansion of the Zr layers upon oxidation. Moreover, the development of residual stresses induced further changes in mechanical properties in relation to the annealing time, as revealed by finite element simulations.