Researcher profile

M. A. Castellanos-Beltran

M. A. Castellanos-Beltran contributes to research discovery and scholarly infrastructure.

ResearcherAffiliation not importedOpen to collaborate

cond-mat.mes-hall cond-mat.supr-con quant-ph

Trust snapshot

Quick read

Trust 21 - Emerging

6works

0followers

3topics

4close collaborators

Actions

Decide how to stay connected

Follow researcher0

Inspect adjacent work, topics, institutions and collaborators without jumping out to a separate graph page.

Building this graph slice

BZPEER is loading the nearby papers, people, topics and institutions for this page.

preprint2015arXiv

Coherent-State Storage and Retrieval Between Superconducting Cavities Using Parametric Frequency Conversion

In superconducting quantum information, machined aluminum superconducting cavities have proven to be a well-controlled, low-dissipation electromagnetic environment for quantum circuits such as qubits. They can possess large internal quality factors, $Q_{int}>10^8$, and present the possibility of storing quantum information for times far exceeding those of microfabricated circuits. However, in order to be useful as a storage element, these cavities require a fast "read/write" mechanism--- in other words, they require tunable coupling between other systems of interest such as other cavity modes and qubits, as well as any associated readout hardware. In this work, we demonstrate these qualities in a simple dual cavity architecture in which a low-Q "readout" mode is parametrically coupled to a high-Q "storage" mode, allowing us to store and retrieve classical information. Specifically, we employ a flux-driven Josephson junction-based coupling scheme to controllably swap coherent states between two cavities, demonstrating full, sequenced control over the coupling rates between modes.

preprint2014arXiv

Fabrication and characterization of large arrays of mesoscopic gold rings on large-aspect-ratio cantilevers

We have fabricated large arrays of mesoscopic metal rings on ultrasensitive cantilevers. The arrays are defined by electron beam lithography and contain up to $10^5$ rings. The rings have a circumference of 1 $μ$m, and are made of ultrapure (6N) Au that is deposited onto a silicon-on-insulator wafer without an adhesion layer. Subsequent processing of the SOI wafer results in each array being supported at the end of a free-standing cantilever. To accommodate the large arrays while maintaining a low spring constant, the cantilevers are nearly 1 mm in both lateral dimensions and 100 nm thick. The extreme aspect ratio of the cantilevers, the large array size, and the absence of a sticking layer are intended to enable measurements of the rings' average persistent current $\langle I \rangle$ in the presence of relatively small magnetic fields. We describe the motivation for these measurements, the fabrication of the devices, and the characterization of the cantilevers' mechanical properties. We also discuss the devices' expected performance in measurements of $\langle I \rangle$.

preprint2013arXiv

Measurement of the full distribution of the persistent current in normal-metal rings

We have measured the persistent current in individual normal metal rings over a wide range of magnetic fields. From this data, we extract the first six cumulants of the single-ring persistent current distribution. Our results are consistent with the theoretical prediction that this distribution should be nearly Gaussian (i.e., that these cumulants should be nearly zero) for diffusive metallic rings. This measurement highlights the particular sensitivity of persistent current to the mesoscopic fluctuations within a single coherent volume.

preprint2011arXiv

Quantum state tomography of an itinerant squeezed microwave field

We perform state tomography of an itinerant squeezed state of the microwave field prepared by a Josephson parametric amplifier (JPA). We use a second JPA as a pre-amplifier to improve the quantum efficiency of the field quadrature measurement (QM) from 2% to 36 +/- 4%. Without correcting for the detection inefficiency we observe a minimum quadrature variance which is 69 +/- 8% of the variance of the vacuum. We reconstruct the state's density matrix by a maximum likelihood method and infer that the squeezed state has a minimum variance less than 40% of the vacuum, with uncertainty mostly caused by calibration systematics.

preprint2010arXiv

Strongly quadrature-dependent noise in superconducting micro-resonators measured at the vacuum-noise limit

We measure frequency- and dissipation-quadrature noise in superconducting lithographed microwave resonators with sensitivity near the vacuum noise level using a Josephson parametric amplifier. At an excitation power of 100~nW, these resonators show significant frequency noise caused by two-level systems. No excess dissipation-quadrature noise (above the vacuum noise) is observed to our measurement sensitivity. These measurements demonstrate that the excess dissipation-quadrature noise is negligible compared to vacuum fluctuations, at typical readout powers used in micro-resonator applications. Our results have important implications for resonant readout of various devices such as detectors, qubits and nano-mechanical oscillators.

preprint2009arXiv

Bandwidth and dynamic range of a widely tunable Josephson parametric amplifier

The ability to manipulate quantum information encoded in microwave fields has led to a renewed interest in Josephson parametric amplifiers (JPAs). For these applications the ability of JPAs to amplify signals with the least amount of added noise is critical. Unfortunately JPAs are typically narrow band amplifiers with small dynamic range. It is therefore important to understand the bandwidth and dynamic range of any particular JPA in order to determine if it is appropriate for these applications. We recently introduced a new kind of JPA. Although it is still narrow band, the amplified band can be tuned over a full octave. We have shown that it has good noise performance and can squeeze the vacuum noise by 10 dB. Here we characterize other important parameters of this amplifier, specifically the signal-bandwidth, dynamic range and saturation power.