Source author record

Arup Ratan Jana

Arup Ratan Jana appears in the imported research catalog. Authorship, coauthor and topic links are available while profile ownership is still unclaimed.

ResearcherUnclaimed source record

physics.acc-ph

Catalog footprint

What is connected

5works

1topics

4close collaborators

Actions

Connect this record

Open graph Browse works

Inspect adjacent papers, topics, institutions and collaborators without losing the researcher page.

Building this map preview

BZPEER is loading the nearby papers, people, topics and institutions for this page.

preprint2016arXiv

Multipacting studies of beta_g=0.61 and beta_g =0.9, 650 MHz Elliptical SRF Cavities

Multipacting is seen as a performance limiting phenomenon for the superconducting radio frequency (SRF) cavities. Numerical simulations are essential to pre-empt the experimentally observed multipacting conditions. Readily available codes(e.g. FISHPACT, MULTIPACT,CST etc.) are widely used to simulate the phenomenon of multipacting in such cases. Most of the contemporary two dimensional (2D) codes are unable to detect multipacting in the elliptical cavities because they use a simplistic secondary emission model, where a constant value of emission kinetic energy of secondary electrons is assumed. Some three-dimensional (3D) codes, which use a more realistic and sophisticated secondary emission model (Furman model) by following a probability distribution for the emission kinetic energy of secondary electrons, are able to correctly predict the occurance of multipacting. These 3D softwares however require large data handling and are slower than contemporary 2D codes. We have developed a 2D code for the multipacting analysis for axisymmetric structures, which is based on the Furman model. Since our code is 2D, it is faster than the 3D codes. This makes it possible to perform an accurate multipacting analysis of multipacting within a resaonalble computational time, thus achieving an accuracy as good as in the case of 3D codes, but requiring significantly less computing time. We have used our code for determining the multipacting prone range of values for Eacc in beta_g =0.61 and beta_g =0.9, 650 MHz mid-cell elliptical cavities that we have recently designed for the medium and high energy section of the proposed Indian Spallation Neutron Source (ISNS) project.

preprint2016arXiv

Reference Physics Design for 1 GeV Injector Linac and Accumulator Ring for Indian Spallation Neutron Source

As a part of the ongoing XIIth plan project titled "R&D activities for high energy proton linac based spallation neutron source", the work on physics design of various subsystems of the injector linac and accumulator ring has been taken up at RRCAT, Indore. For the 1 GeV H- injector linac, physics design studies of individual systems have been completed, and the end to end beam dynamics simulation studies have been performed to ensure that the stringent beam dynamics criteria are satisfied for the optimized lattice. Physics design studies to optimize the linear lattice of the accumulator ring have also been completed. The design studies for the beam transport lines from the injector linac to the accumulator ring, and from the accumulator ring to target are currently in progress. This report describes the physics design of various systems of the injector linac and the accumulator ring.

preprint2013arXiv

A Study of Dynamic Lorentz Force Detuning of 650 MHz βg= 0.9 Superconducting Radiofrequency Cavity

The small bandwidth of superconducting cavities makes the study of dynamic Lorentz force detuning and its compensation indispensable in case of pulsed mode operation of high gradient accelerators. In this paper, we present the study of this detuning and also propose an optimized design for five cell 650 MHz βg= 0.9 elliptic superconducting cavities, which will be used in the high energy section of the 1 GeV H- linear accelerator for the proposed Indian Spallation Neutron Source project, by suitably inserting the inter-cell stiffeners. The paper presents a sequential design methodology which starts with study of static Lorentz force detuning and tunability; and progresses to find out the structural modes and related dynamic detuning values by performing transient structural dynamics calculations. The developed methodology is general in nature and can be used for a three dimensional model of any geometry. The work will be useful for optimizing the design against dynamic Lorentz force detuning of superconducting radiofrequency cavities of any shape.

preprint2013arXiv

On the Electromagnetic Design of a Beta_g= 0.61, 650 MHz Superconducting Radiofrequency Cavity

We present the calculations for electromagnetic design of a Beta_g = 0.61, multi-cell superconducting radiofrequency cavity for the Indian Spallation Neutron Source (ISNS) project. Geometry of the mid-cells is optimized using a step by step, one-dimensional optimization technique. This is followed by the optimization of end-cells, which is done to achieve the required field flatness, as well as to avoid trapping of higher order modes. Calculations of the threshold beam current for the excitation of regenerative beam break up instability excited by the dipole modes is also presented, which is followed by wake field calculations and estimation of its effects. Specific aspects relevant to design calculations for medium Beta_g cavities, compared to high Beta_g cavities are highlighted in the paper. Finally, studies are performed for the static as well as dynamic Lorentz Force Detuning (LFD), based on which the stiffness design of the cavity is optimized.

preprint2012arXiv

Electromagnetic Design of β_g= 0.9, 650 MHz Superconducting Radiofrequency Cavity

We present the electromagnetic design study of a multi cell, β_g= 0.9, 650 MHz elliptic superconducting radiofrequency cavity, which can be used for accelerating H- particles in the linear accelerator part of a Spallation Neutron source. The design has been optimized for maximum achievable acceleration gradient by varying the geometry parameters of the cavity, for which a simple and general procedure is evolved that we describe in the paper. For the optimized geometry, we have studied the higher order modes supported by the cavity, and the threshold current for the excitation of the regenerative beam break up instability due to dipole modes has been estimated. Lorentz force detuning studies have also been performed for the optimized design and the calculations are presented to find the optimum location of the stiffener ring to compensate for the Lorentz force detuning.