BZPEERPapers, people, evidence and research pathsDiscover
Research tools
Network
Opportunities
Account
Source author record
A. S. Bhattacharyya appears in the imported research catalog. Authorship, coauthor and topic links are available while profile ownership is still unclaimed.
Catalog footprint
Research graph
Inspect adjacent papers, topics, institutions and collaborators without losing the researcher page.
BZPEER is loading the nearby papers, people, topics and institutions for this page.
Published work
Zinc oxide and Aluminum Ferrite were prepared Chemical route. The samples were characterized by XRD and VSM. Simulation of M-H plots of Co/CoO thin films were performed. Effect of parameters was observed on saturation magnetization.
Ferric Chloride-Bismaleimide (FeCl3-BMI) and Titania-Bismaleimide (TiO2-BMI) composite were synthesized using PVA as a binder. The composite systems were deposited on glass slide as a homogenous coating. XRD and FTIR studies of the composite system showed its crystalline and structural configuration. A mixed phase of TiO2 and BMI as well as short range crystallinity was observed. An increase in crystallinity with temperature was also seen. The percentage of N-H symmetric stretching was also found to increase with temperature.
Nanoindentation is an effective way of finding mechanical properties at nanoscale. They are especially useful for thin films where elimination of the substrate effect is required. The mechanism is based upon depth sensing indentation based on Oliver and Pharr modeling. Nanoindentation was used to evaluate the nanomechanical and fractographic properties of hard coatings deposited by magnetron sputtering. Radial and lateral cracks accompanied by delamination of the coatings were observed during the indentation tests. A novel phenomenon of stress induced crystallization was observed in case of the CNx films which resulted in crack deflection. Indentations at micro scale using Vickers Indenter were also done and the cracking phenomena were analyzed.
Co and CoO thin films were deposited by magnetron sputtering in the form of multilayers. They were irradiated with Ar and Si ion beams of different energies and fluences. The magnetic properties were investigated.
Bismaleimide (BMI) resins are a new breed of thermosetting resins used mainly for high temperature applications and have major usage in aerospace. FTIR studies have shown the signatures of imide, CNC stretching, malemide and N-H stretching. These BMI polymer coatings were deposited on aluminum and mild steel substrates by sprinkling powers followed by baking. Thermo gravimetric analysis and Differential scanning calorimetric studies showed the degradation temperature of these polymers around 370oC. Aluminum coatings were deposited on BMI previously deposited on Al and mild steel to make a metal-BMI-metal trilayer. These trilayers can solve the problem charging of the aircraft bodies at high altitudes. Atomic force microscopy was done to determine the morphology of the surface. Roughness and thickness measurements of the BMI coatings were carried out by surface profilometer. Vickers microhardness tests showed an increase in hardness of the metal-BMI-metal trilayer. FTIR spectrum showed signature of imides, CNC stretching, maleimide and N-H stretching in BMI. We observed that peak broadens at which shows the release of the stress during thermal treatment of the coating. The coating is subject to variable APPJ conditions which improve the properties at high temperature.
Coatings of ternary nanocomposite Si-C-N ceramic coatings have shown newer and improved mechanical and functional properties over the coarser and monolithic coatings. Properties like high hardness, wear resistance, oxidation resistance, tunable band gap and chemical inertness have been observed for Si-C-N which makes its potential for numerous applications. Although lot of research has taken place in Si-C-N coatings, proper understanding of the effect of different parameters on the coating properties are still not resolved. The changes occurring in fraction of Si, C and N and the phases forming in the coatings with variation in deposition conditions require investigations. This research paper gives a systematic study of the role of different deposition parameters like substrate temperature, pressure, power on the nucleation and growth, structure, microstructural bonding and mechanical properties of the film deposited by magnetron sputtering which adds significantly to the fundamental knowledge of nanocomposite Si-C-N coatings as well as its applications.
Raman studies of nanocomposite SiCN thin film by sputtering showed that with an increase of substrate temperature from room temperature to 500oC, a transition from mostly sp2 graphitic phase to sp3 carbon took place which was observed from the variation of ID/IG ratio and the peak shifts. This process resulted in the growth of C3N4 and Si3N4 crystallites in the amorphous matrix which led to an increase in hardness and modulus obtained through nanoindentation. However, at a further higher temperature of 600oC, again an increase of sp2 C concentration in the film was observed and the H and E values showed a decrease due to increased growth of graphitic carbon phase. The whole process got reflected in a modified four stage Ferrari Robertson model of Raman spectroscopy.
The article consists of four sections all dealing with the computational modeling of the sputtering process. The first section deals with the difference in Bismuth atomic layer deposition at different polar angle and ion flounce. In the second section, atomic layer deposition was studied as a function of incident Argon ion energy at different pressure conditions. A curve analogous to Bragg curve was obtained .In the third section TiOx films was developed by simulations. The sputtering parameters were varied to get different atomic layers. The variation of coverage with sticking coefficient was shown. The last section deals with sputter based deposition of TiN films. The rate of change of partial sputtering yield with coverage was considered. The deposition pressure and time were varied to get films of different thickness. All the sections are stored separately
Bismaleimide (BMI) are thermosetting polymers mainly used in aerospace applications having properties of dimensional stability, low shrinkage, chemical resistance, fire resistance, good mechanical properties and high resistance against various solvents, acids, and water. BMI is commercially available as Homide 250. BMI coating has also been used for the corrosion protection. Metallization (AL) of BMI using vacuum evaporation was done which serves the purpose of prevention of space charge accumulation in aircraft bodies. Addition of inorganic materials like metal oxides can influence the properties of the polymer as an inorganic-organic composite. The organic-ionorganic composites have wide applications in electronics, optics, chemistry and medicine. Titanium dioxide (TiO2, Titania) has a wide range of applications starting from photocatalysis, dye-sensitized solar cells to optical coatings and electronics. A BMI-TiO2 composite was prepared by chemical route. Atmospheric Plasma Jet (APPJ) using Helium gas was also treated on BMI. XRD and FTIR studies of the composite system prepared at different temperatures showed its crystalline and structural configuration.
Epitaxial copper thin films were deposited by magnetron sputtering. The adatoms during deposition are influenced by deposition parameters which cause variations in thin film properties. XRD and FESEM studies were done to get an insight into the growth mechanisms of the films. A modeling has been done on the epitaxial thin film growth with sputtering process. The parameters during sputtering like, sputtering yield, pressure, temperature, current density, deposition time were related and an attempt has been made to analyze the sputtering process.
Bismaleimide (BMI) resins are a new breed of thermosetting resins used mainly for high temperature applications and have major usage in aerospace. BMI polymer coatings were deposited on aluminum and mild steel substrates. The effect of corrosion on mild steel and aluminum by Ringers Solution and there protection using BMI coatings were observed. X-ray diffraction studies showed crystalline nature of the BMI coatings. Surface contact angle measurements were carried out using goniometer.