BZPEERReading, trust and collaboration for researchDiscover
Workspaces
Network
Opportunities
Account
Researcher profile
Saleem James Denholme contributes to research discovery and scholarly infrastructure.
Trust snapshot
Actions
Identity and collaboration
Claiming links this public author record to a researcher profile and unlocks direct collaboration workflows.
Log in to claimDirect collaboration
Claim this author entity first to unlock direct invitations.
Research graph
Inspect adjacent work, topics, institutions and collaborators without jumping out to a separate graph page.
BZPEER is loading the nearby papers, people, topics and institutions for this page.
Published work
We measured the electrical resistivity of a BiS2-based compound EuFBiS2 under high pressure. Polycrystalline EuFBiS2 shows insulator-metal transition and pressure-induced superconductivity above 0.7 GPa. The superconducting transition temperature increases with increasing applied pressure and shows the maximum value around 8.6 K at 1.8 GPa.
The Phase diagram of SmFeAsO1-xFx in terms of x is exhibited in this study. SmFeAsO1-xFx from x = 0 to x = 0.3 were prepared by low temperature sintering with slow cooling. The low temperature sintering suppresses the formation of the amorphous FeAs, which is inevitably produced as an impurity by using high temperature sintering. Moreover, slow cooling is effective to obtain the high fluorine concentration. The compositional change from feedstock composition is quite small after this synthesis. We can reproducibly observe a record superconducting transition for an iron based superconductor at 58.1 K. This achievement of a high superconducting transition is due to the success in a large amount of fluorine substitution. A shrinking of the a lattice parameter caused by fluorine substitution is observed and the substitutional rate of fluorine changes at x =0.16.
We obtained amorphous-FeAs-free SmFeAsO1-xFx using a low temperature sintering with slow cooling. SmFeAsO1-xFx is sintered at 980 °C for 40 hours and cooled slowly down to 600 °C. The low temperature sintering suppresses the formation of amorphous FeAs, and the slow cooling introduces much fluorine into SmFeAsO1-xFx. The superconductivity of this sample appears at 57.8 K and the superconducting volume fraction reaches 96 %. To study the change of fluorine concentration during the cooling process, samples are quenched by water at 950 °C, 900 °C, 850 °C, 800 °C, 750 °C and 700 °C. It is found that fluorine is substituted not only at the maximum heating temperature but also during the cooling process. The low temperature sintering with slow cooling is very effective to obtain a homogeneous SmFeAsO1-xFx with high fluorine concentration.
We have successfully synthesized a new BiS2-based superconductor NdOBiS2 with F-doping. This compound is composed of superconducting BiS2 layers and blocking NdO layers, which indicates that the BiS2 layer is the one of the common superconducting layers like the CuO2 layer of cuprates or Fe-As layer of Fe-based superconductors. We can obtain NdO1-xFxBiS2 with bulk superconductivity by a solid-state reaction under ambient pressure. Therefore, NdO1-xFxBiS2 should be the suitable material to elucidate the mechanism of superconductivity in the BiS2-layer.
We have successfully synthesized FeSe films by the electrochemical deposition in the electrolyte containing FeCl_{2}\cdot4H_{2}O, SeO_{2} and Na_{2}SO_{4}. The composition ratio of Fe and Se was controlled by the synthesis voltage and pH value. The FeSe film with the composition ratio of Fe : Se = 1 : 1 is fabricated at a voltage of -0.9 V and pH 2.1 in our electrochemical deposition. This sample has a highly crystalline tetragonal FeSe structure and exhibits a superconducting transition at 8.1 K, comparable to FeSe synthesized by other methods.