Source author record

Hongchen Miao

Hongchen Miao appears in the imported research catalog. Authorship, coauthor and topic links are available while profile ownership is still unclaimed.

ResearcherUnclaimed source record

cond-mat.mtrl-sci cond-mat.mes-hall

Catalog footprint

What is connected

4works

2topics

4close collaborators

Actions

Connect this record

Open graph Browse works

Inspect adjacent papers, topics, institutions and collaborators without losing the researcher page.

Building this map preview

BZPEER is loading the nearby papers, people, topics and institutions for this page.

preprint2016arXiv

Excitation and reception of pure shear horizontal waves by using face-shear d24 mode piezoelectric wafers

The fundamental shear horizontal (SH0) wave in plate-like structures is of great importance in non-destructive testing (NDT) and structural health monitoring (SHM) as it is non-dispersive, while excitation and reception of SH0 waves using piezoelectrics is always a challenge. In this work, we firstly demonstrate via finite element simulations that face-shear piezoelectrics is superior to thickness-shear piezoelectrics in driving SH waves. Next, by using a newly defined face-shear d24 PZT wafer as actuator and face-shear d36 PMN-PT wafers as sensors, pure SH0 wave was successfully excited in an aluminum plate from 140 kHz to 190 kHz. Then, it was shown that the face-shear d24 PZT wafer could receive the SH0 wave only and filter the Lamb waves over a wide frequency range (120 kHz to 230 kHz). The directionality of the excited SH0 wave was also investigated using face-shear d24 PZT wafers as both actuators and sensors. Results show that pure SH0 wave can be excited symmetrically along two orthogonal directions (0° and 90° ) and the amplitude of the excited SH0 wave can keep over 90% of the maximum amplitude when the deviate angle is within 30°. This work could greatly promote the applications of SH waves in NDT and SHM.

preprint2016arXiv

Excitation of fundamental shear horizontal wave by using face-shear (d36) piezoelectric ceramics

The fundamental shear horizontal (SH0) wave in plate-like structures is extremely useful for non-destructive testing (NDT) and structural health monitoring (SHM) as it is non-dispersive. However, currently the SH0 wave is usually excited by electromagnetic acoustic transducers (EMAT) whose energy conversion efficiency is fairly low. The face-shear (d36) mode piezoelectrics is more promising for SH0 wave excitation but this mode cannot appear in conventional piezoelectric ceramics. Recently, by modifying the symmetry of poled PbZr1-xTixO3 (PZT) ceramics via ferroelastic domain engineering, we realized the face-shear d36 mode in both soft and hard PZT ceramics. In this work, we further improved the face-shear properties of PZT-4 and PZT-5H ceramics via lateral compression under elevated temperature. It was found that when bonded on a 1 mm-thick aluminum plate, the d36 type PZT-4 exhibited better face-shear performance than PZT-5H. We then successfully excite SH0 wave in the aluminum plate using a face-shear PZT-4 square patch and receive the wave using a face-shear PMN-PT patch. The frequency response and directionality of the excited SH0 wave were also investigated. The SH0 wave can be dominate over the Lamb waves (S0 and A0 waves) from 160 kHz to 280 kHz. The wave amplitude reaches its maxima along the two main directions (0° and 90°). The amplitude can keep over 80% of the maxima when the deviate angle is less than 30°, while it vanishes quickly at the 45° direction. The excited SH0 wave using piezoelectric ceramics could be very promising in the fields of NDT and SHM.

preprint2015arXiv

Realization of face-shear piezoelectric coefficient d36 in PZT ceramics via ferroelastic domain engineering

The piezoelectric face-shear (d36) mode may be the most useful shear mode in piezoelectrics, while currently this mode can only exist in single crystals of specific point groups and cut directions. Theoretically the d36 coefficient vanishes in piezoelectric ceramics because of its transversally isotropic symmetry . In this work, we modified the symmetry of poled PZT ceramics from transversally isotropic to orthogonal through ferroelastic domain switching by applying a high lateral stress along the "2" direction and holding the stress for several hours. After removing the compression, the piezoelectric coefficient d31 is found much larger than d32. Then by cutting the compressed sample along the zxt+45 deg direction, we realized d36 coefficients up to 206 pC/N which is measured by using a modified d33 meter. The obtained large d36 coefficients in PZT ceramics could be very promising for face-shear mode resonators and shear horizontal (SH) wave generation in nondestructive testing.

preprint2014arXiv

More ferroelectrics discovered by switching spectroscopy piezoresponse force microscopy?

The local hysteresis loop obtained by switching spectroscopy piezoresponse force microscopy (SS-PFM) is usually regarded as a typical signature of ferroelectric switching. However, such hysteresis loops were also observed in a broad variety of non-ferroelectric materials in the past several years, which casts doubts on the viewpoint that the local hysteresis loops in SS-PFM originate from ferroelectricity. Therefore, it is crucial to explore the mechanism of local hysteresis loops obtained in SS-PFM testing. Here we proposed that non-ferroelectric materials can also exhibit amplitude butterfly loops and phase hysteresis loops in SS-PFM testing due to the Maxwell force as long as the material can show macroscopic D-E hysteresis loops under cyclic electric field loading, no matter what the inherent physical mechanism is. To verify our viewpoint, both the macroscopic D-E and microscopic SS-PFM testing are conducted on a soda-lime glass and a non-ferroelectric dielectric material Ba0.4Sr0.6TiO3. Results show that both materials can exhibit D-E hysteresis loops and SS-PFM phase hysteresis loops, which can well support our viewpoint.