Source author record

Anton Hohenwarter

Anton Hohenwarter appears in the imported research catalog. Authorship, coauthor and topic links are available while profile ownership is still unclaimed.

ResearcherUnclaimed source record

cond-mat.mtrl-sci

Catalog footprint

What is connected

4works

1topics

4close collaborators

Actions

Connect this record

Open graph Browse works

Inspect adjacent papers, topics, institutions and collaborators without losing the researcher page.

Building this map preview

BZPEER is loading the nearby papers, people, topics and institutions for this page.

preprint2026arXiv

Precipitate size evolution in an ultrafine-grained magnesium-manganese alloy

Precipitate size evolution during room temperature high-pressure torsion (HPT) of a Mg-1.35wt.%Mn alloy was studied using scanning transmission electron microscopy (STEM) and Small-/Wide-angle X-ray scattering (SAXS/WAXS). The volume fraction of the nm-scale $α$-Mn particles increased with applied strain, however small angle X-ray scattering (SAXS) indicated that the majority of manganese remained in solution even after 10 HPT rotations, indicating that the reaction progress is still limited by the diffusivity of Mn. Analysis of the precipitate size distribution determined that the mean particle size did not increase over the course of HPT. This, in combination with the precipitate size distribution suggested that precipitate growth was subject to interfacial rather than diffusional control.

preprint2022arXiv

Soft Magnetic Properties of Ultra-Strong and Nanocrystalline Pearlitic Wires

The paper describes the capability of magnetic softening of a coarse grained bulk material by a severe deformation technique. Connecting the microstructure with magnetic properties, the coercive field decreases dramatically for grains smaller than the magnetic exchange length. This makes the investigation of soft magnetic properties of severely drawn pearlitic wires very interesting. With the help of the starting two phase microstructure, it is possible to substantially refine the material, which allows the investigation of magnetic properties for nanocrystalline bulk material. Compared to the coarse grained initial, pearlitic state, the coercivities of the highly deformed wires decrease while the saturation magnetization values increase, even beyond the value expectable from the individual constituents. The lowest coercivity in the drawn state is found to be 520 A m for a wire of 24 um thickness and an annealing treatment has a further positive effect on it. The decreasing coercivity is discussed in the framework of two opposing models: grain refinement on the one hand and dissolution of cementite on the other hand. Auxiliary measurements give a clear indication for the latter model, delivering a sufficient description of the observed evolution of magnetic properties.

preprint2020arXiv

Microstructure and Failure Characteristics of Nanostructured Molybdenum Copper Composites

Liquid-metal infiltrated Cu30Mo70 (weigth percentage) is subjected to severe plastic deformation using high pressure torsion. The initially equiaxed dual phase structure is gradually transformed into a lamellar structure composed of individual Cu and Mo layers. The thickness of the lamellae varies between the micrometer and nanometer ranges depending on the amount of applied strain. Consistent with the refinement of the microstructural features, strength and hardness substantially increase. In addition, an acceptable ductility is found in the intermediate deformation range. An assessment of the damage tolerance of the produced composites is performed by measuring the fracture toughness in different crack propagation directions. The results indicate the development of a pronounced anisotropy with increasing degree of deformation which is an effect of the concurrent alignment of the nanostructured lamellar composite into the shear plane.

preprint2016arXiv

Exceptional damage-tolerance of a medium-entropy alloy CrCoNi at cryogenic temperatures

High-entropy alloys are an intriguing new class of metallic materials that derive their properties from being multi-element systems that can crystallize as a single phase, despite containing high concentrations of five or more elements with different crystal structures. Here we examine an equiatomic medium-entropy alloy containing only three elements, CrCoNi, as a single-phase face-centered cubic (fcc) solid solution, which displays strength-toughness properties that exceed those of all high-entropy alloys and most multi-phase alloys. At room temperature the alloy shows tensile strengths of almost 1 GPa, failure strains of ~70%, and KJIc fracture-toughness values above 200 MPa.m1/2; at cryogenic temperatures strength, ductility and toughness of the CrCoNi alloy improve to strength levels above 1.3 GPa, failure strains up to 90% and KJIc values of 275 MPa.m1/2. Such properties appear to result from continuous steady strain hardening, which acts to suppress plastic instability, resulting from pronounced dislocation activity and deformation-induced nano-twinning.