Source author record

A. Toriumi

A. Toriumi appears in the imported research catalog. Authorship, coauthor and topic links are available while profile ownership is still unclaimed.

ResearcherUnclaimed source record

cond-mat.mtrl-sci cond-mat.mes-hall

Catalog footprint

What is connected

5works

2topics

4close collaborators

Actions

Connect this record

Open graph Browse works

Inspect adjacent papers, topics, institutions and collaborators without losing the researcher page.

Building this map preview

BZPEER is loading the nearby papers, people, topics and institutions for this page.

preprint2014arXiv

Crystal orientation relation and macroscopic surface roughness in hetero-epitaxially grown graphene on Cu/mica

A clean, flat and orientation-identified graphene on a substrate is in high demand for graphene electronics. In this study, the hetero-epitaxial graphene growth on Cu(111)/mica(001) by chemical vapor deposition is investigated to check the applicability for the top-gate insulator research on graphene as well as the graphene channel research by transferring graphene on SiO2/Si substrates. After adjusting the graphene-growth condition, the surface roughness of the graphene/Cu/mica substrate and the average smooth area are ~0.34 nm and ~100 um2, respectively. The orientation of graphene in the graphene/Cu/mica substrate can be identified by the hexagonal void morphology of Cu. Moreover, we demonstrate the relatively high mobility of ~4500 cm2V-1s-1 in graphene transferred on the SiO2/Si substrate. These results suggest that the present graphene/Cu/mica substrate can be used for top-gate insulator research on graphene.

preprint2013arXiv

Carrier density modulation in graphene underneath Ni electrode

We investigate the transport properties of graphene underneath metal to reveal whether the carrier density in graphene underneath source/drain electrodes in graphene field-effect transistors is fixed. The resistance of the graphene/Ni double-layered structure has shown a graphene-like back-gate bias dependence. In other words, the electrical properties of graphene are not significantly affected by its contact with Ni. This unexpected result may be ascribed to resist residuals at the metal/graphene interface, which may reduce the interaction between graphene and metals. In a back-gate device fabricated using the conventional lithography technique with an organic resist, the carrier density modulation in the graphene underneath the metal electrodes should be considered when discussing the metal/graphene contact.

preprint2013arXiv

Estimation of residual carrier density near the Dirac point in graphene through quantum capacitance measurement

We discuss the residual carrier density (n*) near the Dirac point (DP) in graphene estimated by quantum capacitance (CQ) and conductivity measurements. The CQ at the DP has a finite value and is independent of the temperature. A similar behavior is also observed for the conductivity at the DP, because their origin is residual carriers induced externally by charged impurities. The n* extracted from CQ, however, is often smaller than that from the conductivity, suggesting that the mobility in the puddle region is lower than that in the linear region. The CQ measurement should be employed for estimating n* quantitatively.

preprint2011arXiv

Electrical transport properties of graphene on SiO2 with specific surface structures

The mobility of graphene transferred on a SiO2/Si substrate is limited to ~10,000 cm2/Vs. Without understanding the graphene/SiO2 interaction, it is difficult to improve the electrical transport properties. Although surface structures on SiO2 such as silanol and siloxane groups are recognized, the relation between the surface treatment of SiO2 and graphene characteristics has not yet been elucidated. This paper discusses the electrical transport properties of graphene on specific surface structures of SiO2 prepared by O2-plasma treatments and reoxidization.

preprint2010arXiv

Contact resistivity and current flow path at metal/graphene contact

The contact properties between metal and graphene were examined. The electrical measurement on a multiprobe device with different contact areas revealed that the current flow preferentially entered graphene at the edge of the contact metal. The analysis using the cross-bridge Kelvin structure (CBK) suggested that a transition from the edge conduction to area conduction occurred for a contact length shorter than the transfer length of ~1 micron. The contact resistivity for Ni was measured as ~5*10-6 Ohmcm2 using the CBK. A simple calculation suggests that a contact resistivity less than 10-9 Ohmcm2 is required for miniaturized graphene field effect transistors.